Question about 1998 kawasaki KDX 200

1 Answer

Connecting rod is blued alittle should it be replaced

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,418 Answers

Yes, if it has turned, it will not last long under the stress of having lots more fun.

Posted on Feb 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dvd recorder will not turn on.


There are 4 680uf caps that should be replaced. I replaced them with
2 1500uf @25v which is slightly more than 1360uf (2 680uf in parallel) on the power supply board. You might have to bend them over as there are alittle higher.

Jan 12, 2013 | Panasonic DMR-E85H DVD Recorder

1 Answer

2000 Dodge Grand caravan Inner tie rod end


use a pipe wrench also known as a monkey wrench that will work just make sure there is not a lock screw keeping it from turning some aftermarket inner tierods have alittle allen head screw to keep them from turning

Aug 27, 2012 | 2000 Dodge Grand Caravan

1 Answer

Installed pump, ran for awhile and now will not trigger to turn on.


Out of ajustment buy hand move rod up and down if it works move rubber ring down alittle or up alittle Would help if I know what was on????

Feb 27, 2011 | Flotec Electrical Supplies

1 Answer

The table on my saw sticks there are two looks like grommetts that are inside the table arm which slides along the bar when I throw alittle water on it it free's it up for a moment what can I do to solve...


Remove grommets from table.First clean the grommets and the rods; Grommets with rubbing alcohol and the rods with 000 fine steel wool. Then use Silicone spray and spray the inside of the grommets . Then spray some silicone on a rag and wipe down the rods all the way around. Let sit 5 minutes and re wipe, then re-assemble and it should work fine. If it starts sticking again, clean rods with that steel wool and respray with the silicone. Hope this helps!

Dec 15, 2010 | Mk Diamond 159943 MK370K 114Horsepower...

1 Answer

I installed a 1987 monte carlo steering column in my 30 ford hot rod i need the color code of the wires so i can conect the directional signails up


H).l-blu wire connect to left front turn signal J).dk-blu wire connect to right front turn signals K).brown wire connect to hazard/flasher relay output L).purple wire conect to turn/flasher signal M). yellow wire connect to left rear stop hazard light N). dk-green wire connect to right rear stop/hazard light P) white wire connect to stop light swirch output

Jun 25, 2010 | Cars & Trucks

1 Answer

HEF33 flame not turning over, power OK and heater working, all lights on. Flame speed at stop and will not move.


i have pyromaster hef33. flames on my stop moveing also. i took off front glass and logs. then i got a long metal tool and.then i tap the moter that moves the rod that makes the flames move.and also i move the rod back and forth alittle bit. i did put just bit 3in one oil on both ends of the rod. so far its doing better now . this may help some one or it not. i thank the moter or rod was sticking

Jan 02, 2010 | Leisure HOMEPRIDE Electric Fireplace...

1 Answer

I'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.


1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

May 21, 2009 | 2000 Isuzu Rodeo

1 Answer

2000 mercury mountaineer door rod off of key lock.


try one of the new clips , even tho they look different , as the old one is apparently a bad design or broke

Mar 23, 2017 | 2000 Mercury Mountaineer

Not finding what you are looking for?
1998 kawasaki KDX 200 Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...