Question about 2002 Yamaha WR 426 F

1 Answer

My wr426 2002 model idles ok then when you back

My wr426 2002 model idles ok then when you've been riding and you back down the revs it idles high. If you clutch it, it will drop back down. also its done 12000 klms should i get new piston and rings for it. I'm not sure if they have already been done as i didn't buy it new

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Hi
Its only the chutch wire and clutch plate setting...
Just get a new clutch wire and all will be well.
Regards
Berry

Posted on Jan 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine revs


sounds like air getting into carb where it shouldn't, i.e. vacuum pipe from carb to tank or between carb and engine

Mar 18, 2013 | 2007 Honda CRF 150 F

1 Answer

Wont hold an idle revs up and down


Hi, Anonymous and the usual suspects are:
1. Extremely lean fuel mixture.
2. Dirt, rust, water, or ethanol sludge in the fuel system.
3. Sticky throttle cables.
4. Multiple carburetors not in synchronization.
5. TPS sensor out of adjustment or faulty.
6. Wrong spark plugs for the type of service.
7. Throttle bodies not in synchronization (FI)
8. Faulty O2 sensor.
9. Clogged, stuck, or faulty IAC valve.
10. Aftermarket components not compatible with ECM.
For more information about your issue please click on the blue links below. Good luck and have a wonderful day.
How To Fix 5 Common Bike Issues RideApart
http://www.thegsresources.com/_forum/showthread.php?181491-Bike-in-idle-and-rpm-s-go-up-and-down-then-stall
Total Motorcycle Forums
You wont get this engine revs by itself
Symptoms of Lean or Rich carb settings on motorcycle

Apr 10, 2017 | Motorcycles

3 Answers

What is high idle?


When a car is idling it is at rest.The idle setting refers to the engine revolutions or 'revs'.If the setting is increased so that the 'revs' are greater,the engine will not stall at rest.This is 'high idle'!

May 16, 2012 | Cars & Trucks

2 Answers

2002 trailblazer LT (EXT) motor revs up at start-up , seems too high for my thoughts , then comes back down after a couple of seconds , mind you , it only does it after sitting overnight


It would be a help if you could let us know the idle speed when cold?
Vehicles usually have a higher tick over when they;ve been standing and are cold. It would increase by a few hundred RPM and then quickly drop back to normal as the engine warms up....
Regards Johngee10

Oct 26, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Poor idle


Throttle cable needs oiling ,Up for choke on .

Mar 20, 2010 | 2003 Suzuki DR-Z 125 L

1 Answer

Have a toro power stage max model 826LE electric start, runs irre


Sounds like carb. may need adjusting. Take the heat box off to expose carb., there should be 2 adjustment screws- 1 on the bottom of the bowl and 1 on the side of the carb just above the edge of the bowl ( depending how the carb sets off the engine - if the carb comes straight out it will be on the side facing towards the front of the snow blower or if it goes towards the handles then standing other side of the snow blower the screw will be facing you), turn both screws in til they just bottom out the turn them out 1 1/4 turns out then start the machine. While the machine is running at low idle turn the screw on the side of the carb. in (clockwise) a little at a time listening for the engine to start to rev up and then start to rev down, bog or studder then turn back slightly to bring idle back up. Once the idle is up then the screw on the very top of the carb. turn that out to lower idle to a normal idle. Repeat those adjustments till you cant get the idle to go up anymore. Now for the screw on the bottom of the bowl- move the throttle up to max and turn the screw in till you hear it rev up higher and starts to bog or sputter then turn it back slightly to bring the high rev to a smooth rev. That should take care of it. If it does not solve it then the carb may need cleaning then the adjustments done again. If you need more help on this please feel free to ask. Sometimes you have to do process of elimination and you start with the easiest first. Also the adjustments should help with the carbon build up on the plug.

Jan 15, 2009 | Agri-Fab Agri - Fab Snow Blower - 42"

Not finding what you are looking for?
2002 Yamaha WR 426 F Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...