Question about 2006 kawasaki ZX-6R

1 Answer

Ecu fuse keeps blowing wen gas applied wat do i need to do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 224 Answers

Check your charging system. you can connect a digital multimeter to your battery and see the voltage. with your bike off it should be between 12 to 13 volts. after you start the bike it should be between 12.5 to 14.5 volts depending on your idle. when you rev up your bike it should go as high as up to 14.5 to 15 volts. if it goes higher than that, your regulator/rectifier is bad and the overcharging is causing your fuse to blow.

Posted on Jan 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What sensor would cause ecu fuse to keep blowing


Either a shorted wire or the ECU. Sensors run from the ECU, they won't blow the fuse.

Mar 20, 2016 | 2004 Kia Optima

1 Answer

Ecu fuse keeps blowing


ecu is faulty, short or ground in ecu

Dec 10, 2013 | Cars & Trucks

1 Answer

I can't open my trunk or gas door on a 2001 lexus ls 430


At the driver side junction box (DSJB), check the 10A FUEL OPN fuse which is the source of power for the fuel door. The power is applied to the fuel lid opener switch that, when closed, activates the fuel lid opener motor and...POP!

Also at the DSJB, check the 15A ECU-IG fuse which supplies power to BODY ECU 1. At the passenger side junction block, check the 20A P FR DOOR fuse. Next, at engine room relay block 1, check the 10A MPX-B fuse. These three fuses apply to BODY ECU 1 which controls luggage compartment door operation. TSW output from the ECU is applied to the luggage compartment dooe opener switch which, when closed, activates the luggage compartment door opener motor and...POP!

Sep 28, 2012 | 2001 Lexus LS 430

2 Answers

99 vw jettal 2.0 gas fuse 29 15amp fuse keeps blowing-no spark unpluged coil and fuse keeps blowing. help please


Thats the fuse for the ECU, engine control module, and is a 15amp for gas 2.0. i would locate the ECU which is under the center of the plenum in the engine compartment and disconnect the long plug. Check for green discoloration on the multipin connector. Sometimes moisture will get in there and short some of the pins together. Leave ECU unplugged and replace the fuse. If it still blows cause is between the fuse and the ECU.

Dec 27, 2010 | 1999 Volkswagen Jetta

1 Answer

Blowing fuse ecu fuse


you might need a better fuse like if you are useing a 5 amp fuse and it keeps blowing try a 10 amp fuse

Jun 02, 2010 | 2003 Hyundai Santa Fe

1 Answer

1991 Honda Civic SI will not start. #14 fuse which is marked alternator/solenoid keeps blowing when trying to start. I am trying to find out what feeds into this fuse to make it keep blowing. My other...


ok first there could be a direct short in the ecu causing the fuse to blow OR the alternator/starter solenoid could be shorting out and blowing the fuse unhook the alternator and see if it blows the fuse then repeat with the starter and the ecu and let me know what happens

Nov 25, 2009 | Honda Civic Cars & Trucks

2 Answers

I have a 2000 Hyundai Accent that keeps blowing the ECU 1 Fuse. I can change it one time and it will last for three weeks then before you know it I can change it 5 times in one day. What does the ECU 1...


The ECM1 fuse blowing usually indicates that the fuel pump wires shorted inside the tank. If you drop the tank and remove the module, you will probably find the insulation burned off the gray pump wire.

Aug 25, 2009 | 2000 Hyundai Elantra

1 Answer

Blown ecu fuse


ECU= Electronic Control unit. This is what controls all the engine electronics. All the sensors on the engine and other things are routed through the part. What it does is tells the engine how to run. Each sensor plays a specific role. The ECU reads how much are the engine is getting, tells the engine how much gas it needs, etc. Try digging around a salvage and finding a new ECU. Swap it out, and if it is still blowing the ECU fuse then you need to start looking for shorts.

Aug 19, 2009 | 1998 Hyundai Elantra

2 Answers

Fuel ECU fuse keeps blowing (30 amp)


Your fuel pump is internally binding and causing the fuse to blow. Change the pump (and filter while you're back there.)

Jun 14, 2009 | 1993 Jeep Wrangler

1 Answer

My fuel ecu fuse keeps blowing?


Unplug the O2 Sensor and see if it blow again. If it does not the sensor is faulty. Replace with a new one. BTY its in the exhast system.

Jun 13, 2009 | 1993 Jeep Wrangler

Not finding what you are looking for?
2006 kawasaki ZX-6R Logo

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...