2000 Hyundai Accent Logo

Related Topics:

Anonymous
Anonymous Posted on Jan 13, 2010
Answered

Hello I have just had a new clutch fitted into my Hyundai Accent Coupe (2000) and yet the thrust bearing is still noisy and it is notchy going into 2/3 gears and when dropping down from 5th to 4th - any ideas? Many thanks, Chris

Answer This Question
  • Anonymous Jan 13, 2010

    Hello the noise goes when you depress the clutch - any idea on why it is notchy going into gears?
    Many thansk, Chris

  • Anonymous May 11, 2010

    is the noise heard all the time or only when depressing the clutch,the reason i ask is that it might be the front transmission bearing you are hearing, if so transmission will have to come down again.

×

1 Answer

Dan Doherty

Dan Doherty

Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Genius:

An expert who has answered 1,000 questions.

  • Master 1,099 Answers
  • Posted on Jan 13, 2010
Dan Doherty
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Genius:

An expert who has answered 1,000 questions.

Joined: Jan 13, 2010
Answers
1099
Questions
3
Helped
387099
Points
3389

If you used the car with a bad cluth you may have damaged the syncromesh, it nearly always happens in 3rd gear. Sounds like the fault, the syncromesh is part of the gearbox and most often cannot be fixed without a new gearbox.

Testimonial: "Great thank you"

  • Dan Doherty
    Dan Doherty Jan 13, 2010

    thats maybe 2 faults then! the noise go's when pressing the cluthch is definately the thrust bearing. but if its crunching in 3rd thats the syncromesh.

×

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Part number & where to source output shaft bearings for 2003 uk reg 1.6 litre manual Hyundai Coupe.
The easy way is to go to the dealership parts department. They would keep those in stock. Or you go to a spares motor factor like the ones below. They are picking up 'wheel bearings', but they can supply all bearing parts..

Wheel bearing for HYUNDAI Coupe II (GK) - Buycarparts.co.uk

 https://www.buycarparts.co.uk > ... > COUPE (GK)
Hub bearing for HYUNDAI Coupe II (GK) Petrol / 1.6 - 2.7 liters / 2001 - 2009 MY ... G4GC 02/2003 - 08/2009; 2.7 V6 (121 kW / 165 hp) G6BA 01/2001 - 08/2009 ...
Missing: manual ‎' Must include: manual

Wheel bearing for Hyundai Coupe gk - AUTODOC

 https://www.autodoc.co.uk > ... > HYUNDAI > COUPE
Wheel bearing rear and front for HYUNDAI COUPE (GK) from 2001 MY from various OEM part manufacturers. Huge brand selection at low prices ? Hub bearing for ...
Missing: litre ‎output

Transmission output shaft bearing. - Hyundai - JustAnswer

 https://www.justanswer.com > hyundai > 94h1d-transmi...
Jun. 3, 2015 - Transmission output shaft bearing. problem. Our 2005 Hyundai Accent stick shift. Parts errand car. Replaced CV - Answered by a verified ...
 1 answer · Top answer: See the answer on the image
Missing: reg ‎' Must include: reg
Read full answer
Oct 24, 2021 • Hyundai Cars & Trucks
0helpful
1answer

Throttle bearing dry what do i put on it?
you need a new throw out bearing there is no way to oil or lube then they generally are a sealed bearing and last the life of the clutch unless the operator of the vehicle has a heavy foot and rides the clutch
Read full answer
Mar 26, 2012 • 1999 Hyundai Accent
0helpful
1answer

Hi, i own a 2001 Hyundai Accent has run only 38000 kms. Recently replaced my Clutch set and after two months i find that the pick-up is very low and while the RPM raises but pick-up takes its time. What...
By clutch set i'm assuming you mean the mechanical units(pressure plate, clutch plate and thrust bearing) not hydraulic? (clutch master and slave). Sounds like your clutch is slipping. Worn clutch plate would be the most obvious cause of the problem but it could be a faulty pressure plate or even clutch fork.Was your flywheel skimmed/machined to match your new clutch units? If not then it should be. Were the parts that were fitted genuine hyundai parts? If not then failure of the new units is also a possibility.
Read full answer
Mar 28, 2011 • Hyundai Accent Cars & Trucks
0helpful
3answers

My clutch makes a horrible grinding noise when pressed in. How much should it cost to replace the clutch?
$400-up
Read full answer
May 18, 2010 • 2005 Hyundai Accent
0helpful
1answer

Accent coupe 1.3 whats best way to change the clutch, is it engine out or can it be done in situ
trust me, taking the drive unit out to fit a clutch is much easier than trying to lean over and f... about with bits all over the place.......
Read full answer
Apr 13, 2010 • 1999 Hyundai Accent
2helpful
1answer

My Hyundai Coupe 2ltr SE (2000) has been well maintained, my pride and joy!! But yesterday the warning light for ABS came on mid journey(7 miles) then went off. Today it was off at start of same journey...
it could be problem with any sensor of abs of any wheel, it as not a major problem , dont worry check with technician.
Read full answer
Jan 21, 2010 • 2000 Hyundai Accent
1helpful
3answers

Clutch is noisy,when i depress the clutch the noise goes away
this noise is caused by a noisy clutch throw-out/release bearing, that is the part that presses against the pressure plate and disengages the clutch disk, the transmission must be removed to replace this part, so it is best to replace the clutch assembly at the same time, the labor for both is the same, about 5 hours
Read full answer
Oct 23, 2009 • 2003 Toyota MR2 Spyder
1helpful
3answers

2002 Hyundai Accent won't go into gear.
Probably the arm that holds the rtelease bearing in the bell housing has slipped out of place. Get someone to depress the clutch while you check the arm is not loose. If the cylinders are working then its most likely the arm is disconected. If you are lucky you may get it put back in place by looking through the inspection hole but most likely you will have to seperate the engine and gearbox. Sorry I havent better news for you.
Read full answer
Aug 06, 2009 • 2003 Hyundai Tiburon
0helpful
1answer

Wont go into first with out grinding or going in hard
Remove gearbox and replace the whole clutch assemberly.Problem is your thrust bearing as collapsed.Good luck.
Read full answer
Jul 04, 2009 • 1997 Hyundai Accent
0helpful
1answer

How easy is it to replace a noisy clutch thrust bearing. 53 plate Ford Focus 1.6 petrol zetec.
The thrust bearing is normally a part of a new clutch kit.Comprises pressure plate, clutch plate and thrust bearing.You will need to remove the gear box to change the bearing.The bearing basically slides onto the gearbox shaft. Recommend changing all three rather than just the beaing.You may want to get quotes from garages as dealers are expensive.
Read full answer
Mar 08, 2009 • 2003 Ford Focus
Not finding what you are looking for?

View Most Popular

2000 Accent

  • Cars & Trucks

Related Question

Part number & where to source output shaft bearings for 2003 uk reg 1.6 litre manual Hyundai Coupe.

  • Hyundai Cars & Trucks

Related Topics

336 views

Ask a Question

Usually answered in minutes!

Popular Questions

New hyundai i30 has clock

Hyundai Accent Cars & Trucks

Radio Station Keeps Changing Automatically

2006 Hyundai Accent

With the ignition off, the rear tail lights won't turn off

2000 Hyundai Accent

Won't play just says 1CDE on screen

2007 Hyundai Accent GS Hatchback

What does ICDE mean on a Getz stereo MP3 player

2007 Hyundai Accent GS Hatchback

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Hyundai Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...