How do you replace a low beam head light on 05 pacifica driver side

try to actual headlight switch and the window might not be related at all do you still have hi beams?

Here's a link on replacing your light bulb on your VW. Sparky Answers 2001 VW Beetle Changing The Low Beam Headlight Bulb HERE'S A VIDEO,ALSO How To Change Head Light Bulb VW Beetle

Tameko; check video link below, press the helpful button and follow me on fixya for more tips

How to replace install Pacifica headlight and bulb lightbulb

If u have removed a remote starting device I would say u got some wiring wrong need to retrace the wires make sure they are correct

check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

MAKE/MODELS: MODEL/BUILD YEARS:
Chrysler/Pacifica 2005
MANUFACTURER: DaimlerChrysler Corporation
NHTSA CAMPAIGN ID NUMBER: 05V066000 RECALL DATE: March 01, 2005
COMPONENT: Exterior Lighting: Headlights
POTENTIAL NUMBER OF UNITS AFFECTED: 43180
SUMMARY:
Certain sport utility vehicles equipped with Halogen headlamps may experience an intermittent and eventual total loss of headlamp function.
CONSEQUENCE:
The head lights may not operate properly which could result in intermittent or no headlight function. This could impair a driver's visibility, increasing the risk of a crash.
REMEDY:
Dealers will inspect, and replace if necessary, the wiring harness and low beam bulb on both headlamp assemblies. The manufacturer has not yet provided an owner notification schedule for this campaign. Owners should contact DaimlerChrysler at 1-800-853-1403.
NOTES:
DaimlerChrysler Recall No. E04. Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-327-4236

Look it over, get involved and remove whatever screws hold it to the body/fender etc. Most screws are Torx type fastners. No torx sockets or driver bits, your done before you start. Torx have been on veh for 25 years.

From LustyKid.

Check the connector wire for continuity on the low end side with a good OHM meter. You probably have a broken wire connection but can't see it due to insulation. See if you have voltage on the low end side of the plug. No voltage, no light. Probe the wire and find where the current stops. Also make sure you don't have the ground reverse on the plug to the headlight. Before replacing it of course. Or you can cut all the wires and replace with a new connector.