Question about 2004 Husqvarna WR 125

1 Answer

How do i adjust my power valve for more acceleration on husky wr 125 04?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 632 Answers

Fitting some reed power valves might help

Posted on Jun 23, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2002 husky 360 100 year anaverary model and someone has welded a automatic decompression in the head now it keep blowing a hole in the piston.WHY

Hi, Brad I'm not sure why someone would weld a decompression unit in the head unless the threads were bad and it was leaking, if it's faulty it could be sucking air and create a hot spot (you may want to do a compression check) or the heat range on your spark plug is too hot/high or you have a pre-ignition issue.
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
CR125 Keeps Eating Pistons
Husqvarna workshop service manual 2000 WR 250 WR 360 amp CR 250 eBay $25
Husqvarna Motorcycle Parts Fiche Husky Part Numbers
Husqvarna WR 250 2002 Owner Manual

Btw, I’m available to help over the phone in case u need at

Apr 04, 2017 | 2001 Husqvarna WR 360

1 Answer

Kick start husqvarna wr 360 2000 mdl snapped off completely can i use ktm kickstart for this ??

Hi, Dan for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2000 Husqvarna CR 250 WR 250 360 Workshop Service Repair Manual DOWNLOAD...
Husqvarna Motorcycle Parts Fiche Husky Part Numbers
Husqvarna WR 250 2002 Owner Manual

Btw, I’m available to help over the phone in case u need at

Dec 26, 2016 | 2000 Husqvarna WR 360

1 Answer

Why does my 2009 husky 300 have a 2008 wr 250 frame

it is what is called mid year production an some of the parts might be 08

Dec 13, 2013 | 2009 Husqvarna WR 300

1 Answer

Magneto, power wires, ignition

The WR and the OR 390 and 400 required a lighting kit to be purchased as an accessory to be fitted for Enduro/ street legal use. Honestly I would try to find a Chilton's manual for those years, browse thru see if it has what you need before you buy it.
Also quite often they're Online sites & forums dedicated to various manufacturer's.
Husky's (aside from left side kick starting)
are awesome bikes, I am sure the is a HUSKY forum somewhere out there, the older the forum the more information is usually in previous posts or the search engine.

Dec 03, 2013 | Husqvarna WR 400 Motorcycles

1 Answer

Can I adjust the tank pressure on a Husky 1506 compressor. pop off keeps engageing, so I need to adjust so that compressor shut off automatically

Before you change any parts, check that the pop valve is not faulty. Look closely at the pop valve to read set release pressure. If the valve is releasing before marked reading, replace valve instead to one slightly higher. The pressure may or may not be adjustable at the switch (need to replace the switch) depending on switch installed at the factory (parts list does not give enough information). If your switch has a remove-abel cap with adjustment screws/nuts, post again with model number of switch for info on adjustment. Good luck

Oct 06, 2011 | Campbell Hausfeld 5 Peak / 1.7 Running HP,...

2 Answers

The rear brake disk is loose but all the bolts are

Go to this site and get a freebie manual. It sounds as if it was re-assembled without the spring washers that hold it tight. But the manual will give you a better description of how it is suppose to be, so go from there:

Jan 31, 2010 | 2002 Husqvarna WR 250

1 Answer

When the bike is cold it ticks over ok but it cuts out when warm

ive got a wre 125 husky n its fine when cold try and hot ticking over try adjusting the idling screw on carb when started not sure how many turns from the in position

Jun 20, 2009 | 2003 Husqvarna WR 125

1 Answer

Power valve for a wr 200 1985

probably not, go to
they sell parts for all semi-vintage bikes i got parts from tham before and they are good and fast shipping.

Jun 17, 2009 | 2000 Yamaha WR 400 F

1 Answer

Poor mid range power tried jetting never been apart 1000 km on bike wr250 husky 2000 mod could it be power valve

not the valve and probably not the jetting if it was running right. pull out and inspect the reeds, probably needs new ones.

Apr 10, 2009 | 2000 Husqvarna WR 250

Not finding what you are looking for?
2004 Husqvarna WR 125 Logo

Related Topics:

409 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5353 Answers

Steve Banks

Level 2 Expert

232 Answers

Joshua Jennings

Level 2 Expert

62 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides