Question about 1992 kawasaki ZZR 1100

1 Answer

I need to source a wind screen and the 2 front discs for the brakes..... please help!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 196 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a whistling noise coming from my car, this is only when moving. If I apply the brakes or am at a standstill, even if I rev the engine there is no noise. When I had service I was told my front...


Whistling noise is pretty vague. There are several possibilities. The brakes could be the source of the noise. If they're 85% gone they should be replaced anyhow regardless of whether they are the source of the noise. Otherwise the noise will no longer be your biggest problem. Disc brakes do have what is called a worn pad indicator. This is simply a metal tab that scrapes the brake rotor, making an annoying, scraping noise until the brake pads are replaced.
Other than this, there are several possibilities. Where is the noise originating? Could it be wind noise coming from an ill fitted window seal? Vacuum hoses are another noise source, although they usually only whistle when decelerating or at idle.
25264808-oghur34fstfkahwooqgb34m4-3-0.jpg

Nov 01, 2014 | Cars & Trucks

1 Answer

Front disc brake assembly diagram


SECTION 206-03: Front Disc Brake 1999 Escort/Tracer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/06/1998 Front Disc Brake Front Disc Brake System Components
Item Part Number Description 1 1125 Front Disc Brake Rotor 2 2B296 Disc Brake Caliper Locating Pin 3 2B120 Disc Brake Caliper 4 2001 Brake Pads 5 - Copper Washers (2 Req'd) 6 - Banjo Bolt 7 2078 Front Brake Hose 8 2W303 Brake Caliper Bolt- (2 Req'd) 9 2814 Brake Hose Clip The front disc brake system consists of a single-piston front disc brake caliper (2B120) and a ventilated front disc brake rotor (1125). The brake shoes and linings (2001) are held in the front disc brake caliper by two front disc brake caliper locating pins (2B296) and two springs. The inboard brake shoe and lining is equipped with a wear indicator that makes a squealing noise when the brake shoes and linings are worn beyond recommended use.

2010&c18=modelyear&c20=n41287&c35=wsm%2cfront%20disc%20brake%2csxf%2c206-03%2cdescription%20and%20operation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_28.gif

Dec 15, 2010 | 1999 Mercury Tracer

1 Answer

My front disc brake is not working instantly... I need instant breaking performance.What shall I do? my rear disc is working properly but the front disc is slipping a little. please help


Slightly slipping disc brake:

First make sure the rotor and brake are clean and free of all oils. Any amount of oil will impede the brake working properly.

Solution #1 - Replace the front brake pads, when they are worn they will not stop as well. You can also replace with a compound that has more grip.

Solution #2 - Check rotor. If it is too smooth, you may need to take some rough grit sandpaper and make the rotor surface not shiny or smooth. You want the rotor to have a little roughness to it. If the surface is too tough to use sand paper on, then use a dremel with a sanding bit.

Solution #3 - not the most practical, but if the performance is not adequate for your needs, then you can replace the brake with a better quality brake that has greater stopping power.

Dec 10, 2010 | Columbia Sportswear Columbia Anzer Peak...

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

How do you change emergency rear disc breaks on 2001 olds aurora


Fairly similar to regular disc brakes except that you need to turn the caliper to get it to wind back in. DON'T COMPRESS IT WITH A CLAMP AS ON THE FRONTS! This will damage the caliper.

Jan 22, 2010 | 2001 Oldsmobile Aurora

1 Answer

Change break pads


for front pads jack and support car remove wheels remove bolts holding calliper [2]remove spring clip pull calliper off remove pads clean housing fit outer pad slowley push calliper piston in using large grips fit inner pad to piston refitcalliper fit bolts refit spring clip can be awkward pump brake pedal until firm check fluid level rear ones are the same but special tool needed to wind calliper pistons back in note make sure brake discs are in good condition first

Dec 30, 2009 | 2000 Volvo S40

2 Answers

How do i fit disc brakes on a 1966 beetle that has drum brakes?


You will need to purchase a drum to disc brake conversion kit. Not that difficult to install. The kit should have everything you need. Check with EMPI. Good VW parts source.

Jun 29, 2009 | Volkswagen Beetle Cars & Trucks

1 Answer

I need to know the procedure for r and r on a front rotor if this is something that can be done at home with limited tools?


1999 Taurus/Sable Section 06-03: Brakes, Front Disc 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Disc Removal
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly. Be careful to avoid damage or interference with caliper bleeder screw fitting and front disc brake rotor shield (2K004).
  1. ani_caut.gif CAUTION: Handle front disc brake rotor (1125) and disc brake caliper (2B120) assembly in such a way as to prevent deformation of front disc brake rotor , and nicking, scratching or contamination of brake linings/rotor surfaces.
    NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .


    Remove caliper anchor plate bolts and discard. Position disc brake caliper out of the way. Prevent separation of caliper housing from anchor bracket because contamination of guide pin journals can occur.
  1. NOTE: If excessive force must be used during front disc brake rotor removal, the front disc brake rotor should be checked for runout prior to installation.


    If additional force is required to remove front disc brake rotor , apply Rust Penetrant and Inhibitor F2AZ-19A501-A or equivalent meeting Ford specification ESR-M99C56-A on front and rear rotor/hub mating surfaces. First, strike front disc brake rotor between lug bolts (1107) with a plastic hammer. If this does not work, attach 2-3 Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor . Remove front disc brake rotor from wheel hub (1104) assembly by pulling it off the lug bolts.
Installation
  1. If original front disc brake rotor is being installed, make sure rotor braking and mounting surfaces are clean.
  1. ani_caut.gif CAUTION: Failure to clean rust and foreign material from rotor and hub mounting faces when installing new or old front disc brake rotors will result in high rotor runout, which will speed up the development of brake roughness shudder vibration.
    Apply a small amount of Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A or equivalent meeting Ford specification ESE-M1C171-A to pilot diameter of front disc brake rotor.
  1. Install front disc brake rotor on wheel hub assembly.
  1. Install disc brake caliper and new caliper anchor bracket bolts on front disc brake rotor . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: Failure to tighten lug nuts (1012) in a star pattern may result in high rotor runout, which will speed up the development of brake roughness, shudder and vibration.
    Install wheel and tire assembly on vehicle. Tighten lug nuts to 115-142 Nm (85-104 lb-ft) using Rotunda Accutorq® Lug Nut Socket 164-R0303 or equivalent on a 1/2 inch air impact wrench, or use a torque wrench.
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.
  1. Road test vehicle.









May 25, 2009 | 1999 Mercury Sable

3 Answers

My 1996 pontaic grandam shakes when i brake


this could be a warped brake disc.. when you brake do you feel the brake peddle go up and down under your foot??? if you do then this is the problem..Hope this helps

Jan 20, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1992 kawasaki ZZR 1100 Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...