Question about 2008 kawasaki Ninja 250R

Open Question

Turn signal relay wiring for 09 Kawi Ninja 250

I am replacing the turn signal relay on my 2009 kawasaki ninja 250 but i have to splice wires. There are 2 wires connected to the old relay. One is orange. The other is orange and green. One wire on the new relay are red. The other is red and black. I need to know which wire goes to which wire. Ive heard that green and black are generally used for ground wires.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Benimur
  • 6966 Answers

SOURCE: 2002 kawasaki ninja 250 motor on ATV need wiring help

Hi and welcome to FixYa,

To my knowledge, there would only be 3 wires needed from the handlebars that affects the engine:

  • engine RUN/OFF;
  • clutch ENGAGED;
  • engine START.
The first 2 would go to the interlock plus the neutral wire and the sidestand wire. The interlock then sends signals that starter motor can turn and that CDI can fire.

As to the ignition coil, 1 wire is IGN B+12 while the other would go to the CDI and should pulsate when cranking or engine running.

Good luck and thank you for using FixYa.

Posted on Feb 01, 2009

  • 298 Answers

SOURCE: 2003 kawasaki ninja 250 stalls and bogs

Stalling is usually caused by water on the fuel tank. Drain the carburetor, better... clean it. Blow air on the jets and needles. Drain the main fuel tank and check for water residue (brown)... siphone the fuel back to the tank. assemble and install the carburator and you'll be off to a cleaner burn. Also, make sure that the spark plugs are cleaned.

Posted on Mar 15, 2009

  • 149 Answers

SOURCE: how to remove front fairing 250 kawasaki ninja

there are small allen bolts or lock screws.. take them out and it should just come off

Posted on Aug 30, 2009

  • 34 Answers

SOURCE: would the fairing parts of a 2006 kawasaki ninja

Yes I do believe they do. Try going to Powersportseast.com Look in the shopping section on the left of the homepage. You will want to use the parts fische and load the info for your bike. It allows you to see what the dealer parts counter can see. See if this helps. I'm pretty sure the 250 ninja really didn't change until 2008 when it got the BIG overhaul

Posted on Nov 02, 2009

Testimonial: "Thanks Fixya"

abhishek33
  • 1239 Answers

SOURCE: how much is the cost of kawasaki ninja 250 R?

Hi friend,,,
welcome to fixya

It costs about 8500$,,\

IT HAS FOLLOWING SPECIFICATIONS:

1.Compact DOHC Twin cylinder engine. 4 valves per cylinder. Lightweight alloy cylinder head. High-compression, lightweight alloy pistons. Advanced liquid-cooling.
2• Maintenance chores are minimized with an automatic cam chain tensioner, silent-type cam chain, low-friction coating on chain guides, plus a low-maintenance battery.
3• Easy-to-select 6-speed transmission with Kawasaki’s convenient Positive Neutral Finder.
4• Diamond high-tensile steel frame and advanced suspension components including the single shock UNI-TRAK® rear suspension system.
5• Stainless steel disc brakes front and rear. Balanced Actuation front brake caliper for consistent wear and performance.
6• Light overall dry weight, low seat height, electric starter, rider-friendly ergonomics, and a 4 gallon (18 L) fuel tank make the 250R a great introduction to the world of sportbikes.
7• Comprehensive instrumentation includes large speedometer and tachometer.
8• Retractable bungee cord hooks add convenience and style.

if your satisfied with my solution PLEASE RATE IT

thank u...

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will 2009 kawasaki ninja 300 plastics work on my 2008 250 ninja?


Hi, Bobbi after careful deliberation 4 out 5 Kawasaki Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm. For more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
http://mototh.com/files/kawasaki/Ninja_250R/Kawasaki_Ninja_250R_FI-English.pdf
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals
Kawasaki Ninja 250R

Apr 14, 2016 | kawasaki Motorcycles

1 Answer

Why wont my 09 ninja 650 run


Hi, Keith and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Fuel line to the carburetor or throttle body pinched or kinked.
8. Carburetor float stuck.
9. Fuel injectors clogged.
10. Severely discharged or damaged battery you need 12.5 volts or better and be able to pass a load test if necessary.
11. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
12. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and CDI box.
Spark plug cables in bad condition and shorting check for leakage in the dark, cable connections loose, or connected to the wrong cylinders.
13. Ignition timing incorrect due to a faulty MAP, CKP, O2, TPS, sensors.
14. Faulty neutral, clutch lever, or kickstand safety switch.
15. Faulty fuel pump or fuse or relay.
16. Faulty CDI box.
17. A stuck bent or burnt valve.
18. Tip over sensor needs a reset.
19. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2009 Ninja 650R Won Start Please Help
2009 Ninja 650R Won Start Please Help Kawasaki Forums Kawasaki Ninja 650R Service Manual
OEM Parts for Kawasaki
Kawasaki 2009 ER 6f Owner Manual

Apr 01, 2016 | 2012 kawasaki Ninja 650

1 Answer

Need to find out how to put wiring on


Kawasaki Motorcycle Wiring Diagrams

www.classiccycles.org/1852/597943.html
Kawasaki BN125 Eliminator 125 Electrical Wiring Harness Diagram Schematic HERE... Kawasaki GPX600 Ninja GPX 600 Electrical Wiring Harness Diagram ...Missing: tpgs

Kawasaki Motorcycle Service Manuals

www.classiccycles.org/1852/1894.html
Kawasaki BN125 Eliminator BN 125 Workshop Service Repair Manual HERE ...Kawasaki GPX600 Ninja 600 Electrical Wiring Diagram Schematic 1988 to 1991 ...Missing: tpgs

WIRING DIAGRAM thread for all sorts of bikes - Bike Chat Forums

www.bikechatforums.com/viewtopic.php?p=2322761

Oct 11, 2009 - 25 posts - ‎7 authors
this is the new wiring diagram thread, requests allowed .... http://i574.photobucket.com/albums/ss182/hmmmnz1/Honda/th_cb600f.jpgCB600f ...Missing: tpgs

Jan 27, 2016 | Motorcycles

1 Answer

My ignition was tampered with, where I had to replace the ignition. My brother had a 1994 kawasaki ninja 250 that was not working, so I took off the ignition and put into mine. 2009 kawasaki ninja 250r. It...


Hi Vinnyv75, for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. Good luck and have a nice day. 2008 Kawasaki Motorcycle Service Repair Workshop Manuals

Jan 19, 2011 | 2008 kawasaki Ninja 250R

1 Answer

I have a 2009 ninja 250r that i slid and i was wondering how much it would cost to get a turning signal fixed. the front right signal broke off and now the back signal only stays on not blinks when on


hi mate you can installl them your self the are held in by 2 bolts or a nut on the inside just unscrew that and disconnect the 2 wires also you can buy them cheap fom somewhere like ebay

Aug 26, 2009 | 2008 kawasaki Ninja 250R

1 Answer

2002 kawasaki ninja 250 motor on ATV need wiring help


Hi and welcome to FixYa,

To my knowledge, there would only be 3 wires needed from the handlebars that affects the engine:
  • engine RUN/OFF;
  • clutch ENGAGED;
  • engine START.
The first 2 would go to the interlock plus the neutral wire and the sidestand wire. The interlock then sends signals that starter motor can turn and that CDI can fire.

As to the ignition coil, 1 wire is IGN B+12 while the other would go to the CDI and should pulsate when cranking or engine running.

Good luck and thank you for using FixYa.

Jan 20, 2009 | 2008 kawasaki Ninja 250R

Not finding what you are looking for?
2008 kawasaki Ninja 250R Logo

Related Topics:

720 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...