Question about 2007 Enfield Bullet Electra

1 Answer

Bearing of the front wheel need to be replaced every 2-3 months, is it problem related to my bike or is it due to the front disc brakes. Do any of you guys face the same problem and do we have a solution for it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Enfield Master
  • 767 Answers

Bearings should last much longer especially if you fit the genuine ones.
While replacing the bearings it is highly recomended tht the( dust ) seals should also be replaced.
The brake disc has nothing to do wth the bearings.
This time if you have to replace the bearing, get a good brand one SKF or KOYO.
Hope this helps!

Posted on Nov 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change front wheel bearings on a 4 wheel drive dodge nitro?


HUB AND BEARING
1. Raise and support the vehicle.
2. Remove the tire and wheel assembly.
3. Remove the caliper adapter. Refer to Brakes/Hydraulic/Mechanical/CALIPER, Disc Brake - Removal.
CAUTION: Never allow the disc brake caliper to hang from the brake hose. Damage to the brake hose will result. Provide a suitable support to hang the caliper securely.
4. Remove the disc brake rotor. Refer to Brakes/Hydraulic/Mechanical/ROTOR, Brake - Removal.
5. Remove the wheel speed sensor. Refer to Brakes/Electrical/SENSOR, Wheel Speed - Removal.
Fig. 47: HALF SHAFT BEARING BOLTS
6. Remove the axle shaft nut. (if equipped with four wheel drive)
7. Remove the three mounting bolts (1) for the hub. bearing assembly.
8. Remove the hub/bearing.
Installation

INSTALLATION

Fig. 48: HALF-SHAFT BEARING BOLTS
1. Install the hub/bearing assembly to the vehicle.
2. Install the three mounting bolts (1) for the hub/bearing. Tighten the bolt to 130 N.m (96 ft.Ibs.).
3. Install the axle shaft nut. Tighten the nut to 135 N.m (100 ft.Ibs.). (if equipped with four wheel drive)
4. Install the wheel speed sensor to the hub. Tighten the bolt to 13.5 N.m (10 ft.Ibs.). Refer to Brakes/Electrical/SENSOR, Wheel Speed - Installation .
5. Install the disc brake rotor. Refer to Brakes/Hydraulic/Mechanical/ROTOR. Brake - Installation .
6. Install the disc brake caliper adapter. Tighten the nut to 135 N.m (100 ft.Ibs.). Refer to Brakes/Hydraulic/Mechanical/ROTOR, Brake - Installation .
7. Install the tire and wheel assembly. Refer to Tires and WheelsAYheels - Standard Procedure . 5250a498-52fa-4c0c-8687-d0c1ee25e9f7.jpg Auto Repair Help US

Sep 02, 2014 | 2007-2011 HA590245 Dodge Nitro Front Wheel...

1 Answer

Front wheel bearings


first check the pads have not worn down to metal if they have the disc will have to be replaced , if the disc is in good condition and the pistons are free press them back into the cylinders and then the pads can removed .check the master cylinder does not over flow as the pistons are pushed back. Brake fluid is a paint remover. the wheel bearings don't have to be touched to replace pads. After new pads are fitted the brakes will have pumped to bring the pads out to the disc.

Aug 15, 2014 | Cars & Trucks

1 Answer

1992 Taurus LX. I drive 1-2 miles and left front wheel gets extremely hot. I have replaced front calipers, discs, rotors, and front brake lines plus bled system repeatedly. Only things left are Master...


I would say neither. You need to raise that wheel and see if the caliper is retracting enough to let the wheel spin free. If it is locked up, I could be a collapsed brake hose on that wheel. The rubber hoses can do that.
Also check if it is a wheel bearing problem. Is the center of the wheel hot? A bad bearing can heat up.

Jan 21, 2014 | Ford Taurus Cars & Trucks

3 Answers

No rear brakes on 1985 honda goldwing aspencade. What could be the problem ?


Check your rear brake resevoir. Fill it with Dot 4 brake fluid and proceed to bleed the brakes, If this does not resore your braking and there is no sign of a leak on the rear caliper, you will have to replace the seals in the master cylinder, or the complete cylinder.

Jan 30, 2011 | 1985 Honda GL 1200 Aspencade Gold Wing

3 Answers

Vibrations from the front wheel


well you asked for this!!!!
check the fork bushes for any play and that they move freely no jumping about,,,,check the wheel bearings for play,,,heck the head race bearings for play and that they are free to turn with out being *****,
check the swinging arm bushes,,,now if all this is good,,,have your wheel balanced

Jul 03, 2010 | 2000 kawasaki VN 1500 Vulcan Classic...

1 Answer

I have a bad wheel bearing how do I replace it


Hub and Bearing Assembly
ani_caut.gif CAUTION: Do not begin this removal procedure unless the following parts are available:
  • A new front axle wheel hub retainer (3B477) (Step 1).
  • A new inboard halfshaft joint stub shaft circlip.
Once removed, these parts must not be reused during assembly. Their torque holding ability or retention capability is diminished during removal.

Removal
  1. Turn ignition switch to the OFF position and place the steering column in the unlock position.
  1. ani_caut.gif CAUTION: Discard the front axle wheel hub retainer. It is a torque prevailing design and cannot be reused. If loosened, the retainer must be removed and a new one installed.
    Remove and discard front axle wheel hub retainer (3B477).
  1. Raise vehicle on hoist.
  1. NOTE: Make sure steering column is in the unlocked position, and do not use a hammer to separate tie rod end (3A130) from the front wheel knuckle (3K185) . Use extreme care not to damage boot seal.

    Remove cotter pin from tie rod end stud and remove slotted nut. Discard cotter pin and nut.
  1. Using Tie Rod End Remover 211-001 (TOOL-3290-D) or equivalent and Tie Rod End Remover Adapter 211-087 (T81P-3504-W), remove tie rod end from front wheel knuckle.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to remove the nut, or bearing and seal damage will result. Loosen the nut first, then remove nut from stud using the hex hold feature.
    For SHO vehicles, remove vinyl cover from upper link stud.
    Remove stabilizer bar link (5K484) from front shock absorber (18124) .
  1. Remove disc brake caliper (2B120) and support with wire to obtain working space. Do not allow disc brake caliper to separate from the front disc brake caliper anchor plate (2B292) to prevent contamination of the disc brake guide pin journals. Do not allow disc brake caliper to hang from front brake hose (2078) . Remove front disc brake rotor (1125) . Remove front disc brake rotor from wheel hub (1104) by pulling it off the lug bolt (1107). If front disc brake rotor is difficult to remove from front wheel knuckle , strike front disc brake rotor sharply between lug bolt with a rubber or plastic hammer.
    If front disc brake rotor will not pull off, apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to inboard and outboard rotor/hub mating surfaces. Install 3-Jaw Puller 205-D027 (D80L-1013-A) or equivalent and remove front disc brake rotor by pulling on front disc brake rotor outside diameter and pushing on hub center. If excessive force is required for removal, check front disc brake rotor for lateral runout prior to installation. Refer to Section 06-00.
  1. Remove anti-lock brake sensor mounting bolt and front brake anti-lock sensor (2C204) .
  1. Remove and discard lower ball joint nut. Using Remover Adapter 211-211 (T96P-3010-A1), separate lower ball joint from front suspension lower arm (3078) .
  1. Using Rotunda Spring Compressor 014-00781 or equivalent, compress front coil spring (5310) until lower ball joint clears front suspension lower arm .
  1. Using Front Hub Remover/Replacer 204-069 (T81P-1104-C), Two Stud Adapter 205-237 (T86P-1104-A1), Metric Hub Remover Adapter 204-085 (T83P-1104-BH) and Front Hub Installer 204-067 (T81P-1104-A), press front wheel driveshaft joint (3B414) from wheel hub . Wire front wheel driveshaft joint to body to maintain a level position.


    df1570a.gif


    Item Part Number Description 1 204-085 (T83P-1104-BH) Metric Hub Remover Adapter 2 204-067 (T81P-1104-A) Front Hub Replacer 3 — Turn Wrench Counterclockwise 4 — Hold Wrench Stationary While Turning Other Wrench 5 204-069 (T81P-1104-C) Front Hub Remover/Replacer 6 204-067 (T81P-1104-A)1 Two Stud Adapter A — Make Sure Metric Hub Remover Adapter 204-085 (T83P-1104-BH) is Fully Threaded onto 1107 and is Positioned Opposite the Two Stud Adapter 205-237 (T86P-1104-A1)
  1. Remove and discard three hub and bearing retainer bolts from front wheel knuckle .
  1. NOTE: Wheel hub is not pressed into front wheel knuckle . Do not use slide hammer to remove a stuck wheel hub . Do not strike back of inner bearing race. Use of these methods will damage bearing internal parts.

    NOTE: If bearing carrier is corroded to front wheel knuckle , apply Rust Penetrant and Inhibitor D7AZ-19A501-AA or equivalent meeting Ford specification ESR-M99C56-A to the inboard and outboard wheel hub/knuckle mating surface and allow to soak.

    Remove wheel hub from front wheel knuckle .


    f8656a.gif

Installation
  1. NOTE: If wheel hub is damaged or if any end play is detectable, replace wheel hub . End play is not adjustable. If wheel hub is disassembled, the assembly must be replaced.

    Remove all foreign material from knuckle bearing bore for correct seating of new wheel hub.
  1. Lightly lubricate mating surfaces of bearing corner and front wheel knuckle.
  1. ani_caut.gif CAUTION: Knuckle bore must be clean enough to allow wheel hub to be completely seated by hand. Do not press or draw wheel hub into place.
    Position wheel hub in front wheel knuckle . Install three new hub and bearing retaining bolts. Tighten to 83-107 Nm (61-78 lb-ft).
  1. Push front wheel driveshaft joint into wheel hub . Hand start front wheel hub retainer.
  1. Slowly release Rotunda Spring Compressor 014-00781 or equivalent while guiding lower ball joint into front suspension lower arm .
  1. Install new lower ball joint nut. Tighten to 68-92 Nm (50-67 lb-ft).
  1. Install tie rod end into front wheel knuckle . Install new slotted nut and tighten to 47-63 Nm (35-46 lb-ft). If necessary advance nut to install a new cotter pin.
  1. ani_caut.gif CAUTION: Use extreme care not to damage boot seal. Do not use power tools to tighten nut or bearing and seal damage will result. Install nut using hex hold feature to prevent the stud from rotating.
    Install stabilizer bar link to front shock absorber . Install stabilizer bar link nut. Tighten to 77-103 Nm (57-75 lb-ft). For SHO vehicles, install stud cover.
  1. NOTE: Remove rust from the rotor and hub mating surfaces with a medium abrasive pad.

    Install front disc brake rotor and disc brake caliper . Tighten caliper anchor bracket bolts to 88-118 Nm (65-87 lb-ft).
  1. ani_caut.gif CAUTION: The front axle wheel hub retainer must be tightened to specification immediately during installation. If the retainer is not tightened immediately, the nylon lock will set incorrectly, leading to incorrect torque readings and bearing failure. Any front wheel hub retainer that is not immediately tightened to specification or is loosened must be removed and a new retainer installed.
    Install front axle wheel hub retainer . Tighten to 230-275 Nm (170-203 lb-ft).
  1. Install wheel and tire. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
  1. Lower vehicle.
  1. Pump brake pedal prior to moving vehicle to position brake linings.

May 28, 2009 | 1999 Ford Taurus

1 Answer

Rear axle bearing replacement



REAR WHEEL BEARING/ HUB

Removal Procedure
  1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
  2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
    1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
    2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Remove the ABS sensor wire connector.
    4. Remove the four bolts from the control arm.
    5. Remove the hub and bearing from the control arm.
    6. Remove the brake shield from the control arm.
    7. Clean the control arm face and the bore before installing the hub and the bearing.
    Installation Procedure

    Notice: Refer to Fastener Notice in Service Precautions.
    1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
    2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
    3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
    4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
    5. Lower the vehicle.

Feb 14, 2009 | 2002 Pontiac Bonneville

1 Answer

Right front wheel/disc brake? heat up


most likely a brake line causing problem. it is either the rubber hose or caliper sticking. the rubber hose will collapse and cause pressure to stay on the caliper

Nov 14, 2008 | 2001 Dodge Dakota

9 Answers

Frontend problem


that sounds like the pressure regulator of your brakes is broken. The pressure does not release from the left side.
Unless it is the calliper, but i think you already checked that out. Pressure regulator is the main cause for problems like this.
It regulates pressure between back and front side

Jun 27, 2008 | 2005 BMW 7 Series

Not finding what you are looking for?
2007 Enfield Bullet Electra Logo

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Enfield Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

kevin bulsara

Level 2 Expert

234 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Enfield Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...