Question about 2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic

1 Answer

No turn signal or 4 way flashers on 2000 flhtcui , all other lights working

Posted by on

  • 1 more comment 
  • Bill Fleming Nov 17, 2009

    after following your proceedure Everything checks out fine but still no trun signal or 4ways, could it be the module itself??? shows HDC68620-96 I think this is the part#

  • Bill Fleming Nov 17, 2009

    I only have a 6 pin module pin 1 orange pin 2 yellow/red stripe pin 3 blank pin 4 yellow pin 5 blank
    pin 6 black.

  • Bill Fleming Nov 22, 2009

    Note: the TSM was located under seat back of tank side not under fearing where the Owner manual and other manuals states, your instruction are great the problem is the TSM.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 124 Answers

The turn signal module gets it's power from the accessory fuse. If the fuse is good, check for 12 volts at the #2 position on the turn signal module (located on the top fork bracket). On the turn signal module the #1 wiring pin position is ground and the #2 wiring pin position is 12 volts dc. If there is no voltage using those two pins, check for resistance between pin #1 and engine ground. If resistance is greater than 1 ohm you have a broken or poor ground wire. If resistance is less than 1 ohm check for 12 vdc on both sides of the accessory fuse. If you have 12 vdc to only one side, replace the fuse. If you have 12 vdc to both sides of the fuse you have a broken wire between the accessory fuse and the turn signal module. If you do not have 12 vdc to the accessory fuse you have a broken wire from the ignition switch and the fuse block.

Posted on Nov 16, 2009

  • gestern1 Nov 17, 2009

    If everything in my previous post checks out you are ready to go futher with more testing on the module. If you have 12vdc at pin 2 using pin 1 as ground you need to check if there is 12vdc at pin 7 with the right turn signal depressed. If you do, check for 12vdc at pin 8 with the left turn signal button depressed. If you have 12vdc on both of those pins place a jumper wire between pins 2 and 3. If the right turn signal lamps illuminate, remove the jumper wire and place it between pins 2 and 4. If the left turn signal lamps illuminate the module is bad.If you did not get 12vdc on any of the above tests, let me know and I will direct you to more diagnostics.

  • gestern1 Nov 17, 2009

    When you are looking for the turn signal module, it has a 8 pin gray Deutsch Connector. The wires going to it are: #1 - Black, #2 - Orange/white, #3 - Brown, #4 - Violet, #5 - White/Green, #6 - not used, #7 - White/Brown, #8 - White/Violet.
    Hope this helps.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left side turn signals not working


Hi Anonymous, you could have a faulty module, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all connector pins are corroded, broken, or loose. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics

Nov 19, 2013 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I have a 2000 dodge 3500 and the brake lights and flashers don't work but turn signals do work


work on one thing at a time, brake lights first, check the brake switch, is it mounted ok ? is power geting to it ? replace if any doubt. check all fuses, replace 4-way flasher, cheap fix . a repair manual has good info, including wire diagrams, for all circuits, etc.,,.. check wir harness @ rear of truck, & along frame for damage, corrosion, etc.,.

Jan 29, 2013 | Dodge Ram 3500 Cars & Trucks

1 Answer

Left turn signal stops working


Had simular problem with wife 2000 Jeep Cherookee.
My signal light were not working at all.Check flasher relay under steering colum

Nov 28, 2012 | 2000 Jeep Grand Cherokee

1 Answer

All light on the car work but the turn signals dont work at all on 2000 dodge grand caravan


Assuming the fuse for the turn signals ia not blown, it sounds like the flasher unit is faulty. most vehicles have separate flashers for 4-ways and directionals so one may work while the other doesn't. Sorry, but don't recall the location of the flasher for that vehicle, but a parts store should be able to look it up for you.

Aug 17, 2011 | 2000 Dodge Grand Caravan

1 Answer

Left turn signal works / don't work, brake light


possibly flasher unit faulty
or turn signal switch

Feb 22, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2000 Intrepid turn signals stopped working, I replace the flasher relay, still turn signals not working?


did you replace the turn signal flasher or the emergency flasher? turn on the emergency flasher lights and pull that flasher if they quit working you changed the wrong one.

Jun 25, 2009 | 2000 Dodge Intrepid

2 Answers

2000 Jeep Cherokee Sport Turn Signals/Hazzard lights don't work


yes that's correct... you need to replace the flasher unit

Feb 23, 2009 | 2000 Jeep Cherokee

1 Answer

Turn Signals work intermitently on 2000 Dodge Ram 1500 Pickup


My turn signals worked fine until last night when I ran my battery down and had to get a jump. I realized right away that my turn signals suddenly didn't work. My theory hasn't been tested, but I am going to unhook my battery cables and reconnect again to see if that does anything. If not, I'll check out the steering wheel and that big square thing by the fuses. Thank you for all the posts and I was so happy to find this web page!

Dec 05, 2008 | 2000 Dodge Ram 1500 Truck

Not finding what you are looking for?
2000 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

801 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...