Question about 2003 Suzuki SV 1000 S

1 Answer

No pressure in suzuki sv1000s rear brakes. tried bleeding, cant get any pressure

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 124 Answers

If the linkage from the brake pedal to the master cylinder is okay, there would be only two reasons you have no pressure at the brake caliper. One would be a broken hose (you would notice brake fluid on the ground). The other would be air in the system. Using a vacuum brake bleeder (Harbor Freight) connect the bleeder hose to the bleeder valve screw on the caliper. Make sure that the master cylinder is full. Apply vacuum to the caliper bleed screw and then loosen the screw watching the vacuum needle on the bleeder tool. When the needle goes to about 5 tighten the bleed screw and then apply vacuum with the bleeder tool and again loosen the screw. You will have to do this numerous times to **** the air/fluid out of the system. Do not pump the vacuum bleeder tool while the bleed screw is open. Make sure the master cylinder does not run low of fluid while you are performing this vacuum bleed.

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I cant get brake to bleed on the left rear and right front on a 2007 Suzuki xl7


Hi, you will have to make sure the bleed nipple is not blocked.

Feb 23, 2016 | Cars & Trucks

2 Answers

2007 suzuki bandit 1250 abs rear brake problems


could be the master cylinder is bad. or you have air in the system. you can try bleeding the brakes to see if you have any pressure

Aug 26, 2014 | Suzuki Bandit 1250S ABS Motorcycles

1 Answer

I changed the rear brake pads on 05 Suzuki Boulevard S83 and after pumping the brake pedal I still have no pressure in the lines to engage the brakes?


Bleed the brake system, or have someone familiar with simple hydraulic systems bleed it. Bleeding removes all the air from the lines.

Aug 12, 2013 | Suzuki Boulevard S83 Motorcycles

1 Answer

Bleeding the brakes ,But no fluide in the rear brakes


Check the master cylinder, pump up the brakes and crack the line at the master cylinder to the rear brakes, if no pressure and it was ran empty or is new part, bench bleed the master cylinder and recheck for pressure at the master cylinder, if you have pressure follow the brake line to the proportioning valve and crack that line before and after the fitting, good luck.

May 09, 2011 | Suzuki Sidekick Cars & Trucks

1 Answer

Rear brake not responding well, minimal braking when pressure applied even when lever is all the way down?


Hi, the lever should not go all the way down, sounds like you have air in your brake system, check your brake pads, if they are ok than bleed the rear brake system, the lever should never bottom out.

Mar 28, 2011 | 1998 Suzuki GSF 600 N Bandit

1 Answer

Brake pedal falls after stopping on 1995 suzuki sidekcik. replaced master cylinder and two rear wheel cylinders and bled system but issue still there. Brakes work fine but after you come to a complete...


I think u got problem on ur rear brake regulator, check that regulator that is located between the two rear brake lines.

The purpose of that barke pressure/limiter regulator is to control the hydraulic pressure on both rear brakes, bleed that and check if the and clean it.....

Dec 02, 2010 | 1995 Suzuki Sidekick

3 Answers

Trying to bleed brake line after replacing rear rotors and pads.. not getting any pressure..


have you had problems getting pressure to the rear brakes before? if yes it is proportion valve problem if no try to sequence bleed the entire system starting with tire left rear, right rear, left front, right front. do the sequence 2-3 times.

Feb 23, 2010 | 2000 Chevrolet Blazer

1 Answer

Can't get caliper off to change there rear brake pads on my suzuki dr350se.


i will assume the pads are tight against the disc?, release the pressure by undoing the bleed screw, don,t forget rebleed the brake..

Oct 31, 2009 | Suzuki DR 350 S Motorcycles

1 Answer

Rear brake bleeding problem


need a little more information.

if you are trying to bleed the brakes you can have someone push the pedal while you loosen the line just enough to allow air to escape. When it stops popping and cracking and only fluid comes out tighten it back up with pressure on the pedal. pump the pedal before loosening line to allow pressure to build up.

or by a vacuum pump and you can do it yourself $10-$40

Oct 15, 2009 | 2000 Suzuki Vitara

1 Answer

Rear brakes might be locked up???


Firstly it might be an idea to release the brakes so you can get the vehicle to a suitable place for repair. Something has gone wrong in the brake master cylinder or the pressure valve (if fitted) although I suspect the former. The hydraulic pressure can be released by loosening the nut on the brake pipe that goes to the rear brakes or undoing the bleed nipples on the rear cylinders a couple of turns. Try to bleed the brakes enough to get them working and then drive to a place of repair. Otherwise remove the master cylinder, strip down and repair or replace.

May 22, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2003 Suzuki SV 1000 S Logo

647 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...