Question about 1981 Suzuki TS 185

1 Answer

The motorbike wll start tick over but when you rev it , it dies

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Clean carb or piston rings need replacing or even the spark plug

Posted on Nov 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alternator battery bad


Does it have any oil in the engine?

Jan 29, 2014 | 2000 Daewoo Nubira

1 Answer

Vfr 400 nc30 misfire


hi all got a nc 30 vfr 400.strugle to start it there is spark on all 4.have to hold the start in for like 1-3min then it starts ony if i give it some revs but it doesnt rev past 3000rpm it just dies and doesnt start for like a day then same story again.dont know if it is carbs of what

Feb 26, 2012 | Motorcycles

1 Answer

My quad wll tick over and revs but will not move it has automatc gears too


i would look to make sure that it isn't in neutral or confirm that it is fully in drive or reverse if not take it to a certified dealer for repair.... sounds like the tranny to me

May 16, 2011 | Quad Cycling

1 Answer

My craftsman chainsaw is pretty new, and it isn't starting properly. When it does start, it has a tendency to cut out during use. I adjusted the idle time, a few times, cleaned the air filter, and checked...


There will be three screws on the carb, the tick over screw, a L screw which ajust the mixture from idle to half throttle, ans a H screw which adjusts the fuel running speed, they are both fuel screws not air screws, start with a basic settinf of one and a half turns on each from closed, with the saw idling gently screw the L screw in, the revs will start to increse as the mixture weakens off, it will reach a point where it starts to die, at this point start unscrewing the L screw, the revs will increse again and then start to die because its too rich, now turn it in 10 minutes on a clock face, check that it revs cleanly,adjust the idle screw so as the chain does not rotate around the bar, the H screw controls the max rpm, this should be set with a rev counter, it should not exceed 12500rpm

Apr 21, 2011 | Garden

1 Answer

My bike is dying at low revs in 30 zones and smells of petrol


its running too rich , too much fuel and needs tuning .

Sep 26, 2009 | 2000 Triumph Sprint ST

1 Answer

My 1996 Suzuki GS500 idles fine but when opening the throttle they die before picking up then it ticks over at 4000RPM,, PLEASE HELP?


have you tried the obvious route of a restricted air flow or even might have a restrictor fitted to it or is it just started doing this

Jun 02, 2009 | 1996 Suzuki GS 500 E

1 Answer

04 citation wont tick over


You need to have a tech II plugged in to see which sensor is playing up .

Jan 12, 2009 | 2002 Isuzu Trooper

Not finding what you are looking for?
1981 Suzuki TS 185 Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...