Question about 2002 Honda CR 125 R

1 Answer

Cr125 wont take fuel in carb when i twist trottle, it is a 99 and the slider is moving.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

Take the fule pipe off the carb and turn fule tap on to see if fule is coming out of the tank,,if it is,,strip carb and clean all the running jets out,,, dont go poking wire into them as this will do more harm than good,, just blow them out with comprest air,, check flote velve as well,,
hope this helps you out

Posted on Nov 14, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1985 cr125 just replaced the head gasket and lower gasket now it wont run ive rebuilt the carb has good compression and its getting fuel into the combustion chamber. well run the first time when...

possibility that even though you have good compression the pressure below the piston is possible leaking past the crank seals ! weak draw on fuel in !

Feb 16, 2014 | Honda CR 125 R Motorcycles

1 Answer

My 02 R6 has been sitting for the past year. I put new gas in the tank and have a new battery. It will start but when I twist the trottle it shuts down (if as it's flooded). Any ideas on what the...

is this the fuel injections model or the carb model?...if its the carb model..sounds like you need to strip the carbs down & clean the float bowls out. & the main jets & dont for get the piolt jet as if petrol let in carbs it goes off & gums them up...if its fuel injections one...could be a sensor!!..hope this helps

Sep 04, 2010 | 2002 Yamaha YZF-R6

1 Answer

01 626 six started died started died has no spark now will not start had icm ck ok

Check your fuel rail pressure.With engine off,key on and cold wearing protective eyewear, remove cover cap relieve schader vavle, just like tire valve stem, on fuel rail with a eyeglass repair scewdriver($.99) at a drug store) the tecnnitions miracle pocket tool) by depressing the valve.No spurts.Fuel presure=low.Got gas? Check trottle position sensor with ohmeter 0 throttle 8-14volts at full open on the trottle lever(located @trottle body hub. Next step obd test by a pro.

Oct 31, 2009 | 1999 Mazda 626

2 Answers

99 blazer wont start. there is combustion, fuel, fuel pressure is 50-60. try to change the all the ignition system and nothing happen just the same result. nothing wrong with the heads and the gasket....

Well sounds like you have the three things an engine needs to work, compression, igintion, fuel! So If you really have those three then it would be a timing issue. Or you are not getting fuel to the cyliners. Like the injectors are plugged maybe
What are your compression numbers?
Also does it try and start at all or just cranks and cranks?
Try and spray a little carb cleaner in the trottle body and see if it trys to run for a few seconds, it if does then that means the injectors are not getting fuel to the engine!
Report back with your findings

Oct 27, 2009 | 1999 Chevrolet Blazer

1 Answer

When its running the trottle linkage varies with fuel spirts and moves with idel going up and down.

look at the bottom of the carb and see if it has a screw there.if so adjust this screw until the idle smoothes out. hope this helps you

Oct 16, 2009 | Garden

2 Answers

Homelite whipper wont start. Replaced the primer

check your gas and oil mix remove the plug take some carb cleaner spray in plug hole pull start replace plug pull start if it fire you mix is wrong.....Good Luck

Aug 15, 2009 | Homelite Consumer Products 4.0 Amp, 13 In....

1 Answer

Honda CR125 Motocross bike throttle delay

ALWAYS have a fire extinguisher on hand when working on carburetors.
Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Now pull the top cap off the throat of the carb and remove the large slide. There will be a long needle in the center of the slide. Remove the needle and then move the clip at the top on the needle down one notch. Two notches may be required but start with one notch. Put it all back together and try it out. Moving the clip downward richens the low end fuel mix.

A “very helpful” rating for this answer? Thanks!

Jun 11, 2009 | 2003 Honda CR 125 R

1 Answer

Cr125 problems with acceleration

Hi,try the stator, may need rewinding.

May 18, 2009 | Honda CR 125 R Motorcycles

1 Answer

Cr125 dead

fuel bowl is stuck... rather the pin the moves with the float bowl... try tapping the float bowl with a scewdriver (not hard enogh to break it) if that doesn't work you have to likely take the carb off and clean it.

Apr 06, 2009 | 2002 Honda CR 125 R

1 Answer

Hi i have a cr125 on a 96 it starts with a bump and when warm kicks up quite nice but now it wont start at all i have tried a new plug got a spark ,compression is fine, plenty of fuel ,drained the carb...

You may need a carb kit. Sputtering is usually one of two things. 1) bad seals in the carb, install a kit.

2) water in the fuel.
Clean the pitcock water trap, check the air cleaner, drain the carb

The generator stuff sounds pretty weird and off the wall.

Mar 14, 2009 | Honda CR 125 R Motorcycles

Not finding what you are looking for?
2002 Honda CR 125 R Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

76070 Answers


Level 3 Expert

4339 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides