Question about 2005 Yamaha TT-R 125 L

1 Answer

2005 TTR 125 will not shift into first gear Hello, I have a 2005 ttr125 that was shifting fine. We replaced the clutch plates and springs, oil and air filter. After we did this, I'm having trouble getting it into first gear and neutral. If I hold the shifter down with my foot and slowly let out the clutch it will go into first and ride OK. All other gears seem to be shifting fine. Is this an adjustment somewhere? The shift lever is somewhat loose, not extremely loose, but about 1/2 inch of play. Could this be it? My other thought was that it had something to do with the screw adjuster in the middle of the pressure plate on the clutch? Any ideas?

Posted by on

  • twozeroone Nov 13, 2009

    Hello Mxtras, thanks for the reply. If I pull in the clutch and hold my foot on the shifter pushing down it will go into first gear. While holding my foot on the shifter I can let the clutch out and ride around in first gear. Once I take off I can let my foot off the shifter and it stays in first, but the shifter stays down, it doesn't come back up like it typically would with a smooth shift.

    I just ordered a new 17.5 pilot jet for it as it doesn't idle due to the previous owner removing the baffle. I ordered a billet tip for it.

    When replacing the clutch I stripped a pressure plate spring bolt and had to replace with another from the hardware store. The bolt was almost identical, but the washer was slightly less thick.

    My fear is that 1st gear broke some teeth off and I'll need to split the cases. Hoping that this is not the problem... It would be a coincidence if it were seeing it was fine pre clutch, and not fine post clutch.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 194 Answers

This is one of those issues that is really tricky to diagnose over the net but would likely take a few minutes to diagnose in person.

When it does drop into gear, does it jump or stall? Will it idle in gear, stopped with the clutch pulled in?

My initial thought is that the clutch is not being fully released (the plates are still in firm contact with eachother).

More than likely, the resolution is a fairly simple adjustment.

Posted on Nov 12, 2009

Testimonial: " "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Yamaha TTR 125 E only starts in neutral


Hi, Dani the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
05 TTR230 only starts in neutral
Part 78 How to eliminate neutral switch and why to do so ZIpty product...
http://www.yamaha-motor.com/assets/service/manuals/2007/lit-11626-20-01_ttr125all_1961.pdf
https://www.partsfish.com/page/oem-parts-for-yamaha
2006 Yamaha TTR125 Owner Manual

Jul 05, 2018 | 2006 Yamaha TTR 125 E

1 Answer

How to rebuild a 2002 Yamaha TTR 125 clutch


Hi, Trevor for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
TTR 125 Clutch Replacement Question
2001 Yamaha TTR 125 Clutch Removal
YAMAHA TT R125 Owner Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
2002 Yamaha TTR125 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Oct 27, 2017 | 2006 Yamaha TTR 125 E

1 Answer

My 2005 Pontiac Bonneville GXP will not shift into 4th gear I was to it was a fourth gear band but is that the only problem that will cause itI'notto shift into 4th gear


Which transmission does yours have 4T65-E or 4T80-E ?

4T80-E
No Fourth Gear

Checks

Causes

1-2 Shift Solenoid Valve
?€¢
Inoperative
?€¢
Debris
?€¢
Pinched wires

3-4 Shift Valve Bore Plug

Misassembled

4th Band

Burned, slipping, missing

4th Servo Cover

Cracked

4th Servo Pin

Broken, seized

4th Servo Piston

Damaged

4th Servo Seals

Rolled, cut or damaged
4T65-E
Slipping or No Fourth Gear
Slipping or No Fourth Gear Checks
Cause

DEFINITION: A large engine RPM increase is noted in fourth gear, Drive range, with little or no vehicle forward speed increase. First, second, and third gear operation are normal. Shifts into fourth gear are soft or do not occur. Fourth gear ratio is 0.705:1.

Automatic Transmission Fluid Level
Low fluid level

Transmission Main Line Pressure
Low transmission main line pressure

Oil Filter Assembly
• The oil filter assembly (100) is missing, plugged, or damaged.
• The oil filter seal assembly (101) is missing or is damaged.

Control Valve Body Assembly
• The 3-4 shift valve (362) or the 4-3 manual downshift valve (360) is stuck or binding.
• Debris is found in the passages of the control valve body (301) or of the control valve body spacer plate and gasket assembly (396)

Case Cover Assembly
Distortion or damage occurs at the manual valve (404) or at the case cover (401), causing PRN oil leak.

Driven Sprocket Support Assembly
A plugged third clutch oil passage in the driven sprocket support assembly (609)

Fourth Clutch Assembly
• The clutch plates (500-502) are worn, damaged, or misassembled.
• A missing or not seated fourth clutch spring retaining ring (601)
• A damaged spring assembly (602) or piston (603)
• Worn or damaged fourth clutch piston seals (604, 605)

Third Clutch Sprag Assembly
• The sprag (720) was misassembled or backwards on the inner race (661).
• A damaged third clutch sprag assembly (653, 661, 719-721)

Dec 06, 2015 | Pontiac Cars & Trucks

1 Answer

2005 Kawasaki KX 125 stuck in 2nd gear will not shift


Hi, Ian and the usual suspects are:
1. Improper clutch adjustment or not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Transmission problems 2004 KX125
KTM stuck in gear or wont shift repair
Kawasaki KX125 Service Manual
OEM Parts for Kawasaki
2005 Kawasaki KX125 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Aug 12, 2013 | 2005 kawasaki KX 125

1 Answer

My ttr 125 makes a clicking noise only in first gear and only when some one is on it if the bike is on a stand noise stops and bike works perfectly


Hi, Braydenw22 I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH
2. Belts---CHIRP
3. Brake Rotors---BUZZ
4. Chains---RATTLE
5. Clutches---CHATTER
6. Shifting Trans---CLUNK
7. Gears---WHINE
8. Front Forks---PLUNK
9. Rear Shocks---SQUEAK
10. Starters---CLICK
11. Solid Lifters---TICK
12. Hydraulic Lifters---TAP
13. Pistons---SLAP
14. Connecting Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
TTR125 first gear clicking
TTR125 First Gear clicking TTR
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
YAMAHA TT R110E Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 21, 2013 | 2006 Yamaha TTR 125 E

1 Answer

2005 Kawasaki KX 125 stuck in 3rd gear.


Hi, Anonymous and the usual suspects are:
1. Improper clutch adjustment or not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
KX stuck in gear
2007 KX 125 won shift into gear
03 08 Kawasaki KX 125 250 Service Manual pdf
OEM Parts for Kawasaki
2005 Kawasaki KX125 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 25, 2012 | 2005 kawasaki KX 125

1 Answer

2005 yamaha ttr-125 will shift into 1st and neutral fine but will not shift into any other gears.


Hi, Fmarules and the usual suspects are:
1. Clutch not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
TTR 125 Will not go into gear
2005 Yamaha TTR 125 Shifter Repair
Yamaha TT R125EW Owner Service Manual
OEM parts for Yamaha
Yamaha TT R125E Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 16, 2012 | 2005 Yamaha TT-R 125 LE

1 Answer

2003 Kawasaki KX 250 won't go into neutral


Hi, Anonymous and the usual suspects are:
1. Improper clutch adjustment or not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Won go into neutral
03 kx 85 wont go into neutral
https://www.howtomotorcyclerepair.com/images/Kawasaki-KX-125-KX250-Service-Manual-2003-2004-2005-2006-2007-2008.pdf
OEM Parts for Kawasaki
2003 Kawasaki KX250 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 22, 2012 | 2003 kawasaki KX 250

1 Answer

Whenever I shift (at a stop) from neutral to first the whole bike either shifts/jolts or occasionally grinds the gears. The clutch is fully depressed when doing so. Thoughts on how to fix or what is...


Your idle may be set too high . 800 to 1000 RPM should be about right. That can cause problems shifting from a stopped position.You may have the wrong oil in your cycle . Do not use car oil or any oil that says Energy Conserving on the label . It will shorten the life of your wet clutch and transmission gears. Use oil that has the JASO MA certification on the label. 10w-40 cold climate or 20w-50 hot climate. A synthetic oil will help you run cooler and shift easier in hot weather conditions and under all conditions. One other thing to check is your clutch plates , if the bike sat for a number of years, the clutch plates could be stuck together. Take off the clutch cover , take off the springs, take off the clutch pressure plate, and pull all the plates out. Carefully separate the plates, replace any scored or burnt plates , rub oil on all the surfaces, and put them back in. This will make the clutch work smoothly if the plates were causing the problems.

Sep 05, 2010 | 1985 Yamaha XJ 700 X Maxim

1 Answer

The bike will not shift into gear. The clutch has plenty of spring tension just will not engage


if the bike has been sitting for a while the clutch plates can stick together, you will still feel spring tension from the pressure plate. two ways to free it up.
with the engine stopped click it up into top gear, put the front wheel against a wall, pull in the clutch, and push on the kick start, or push start it in gear, pull in the clutch and vary the throttle .
Change the oil after the ride with good motorcycle engine oil.

Apr 26, 2010 | 2003 kawasaki KLX 125

Not finding what you are looking for?
2005 Yamaha TT-R 125 L Logo

843 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

vince

Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...