Question about 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

I have a poor connection on my front turn signals on my 2001 HD Deuce.The connector plate was broke so I replaced them. Now the connection is as bad as the broken one. Any suggestions on how to improve this connection?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

I'm not sure which connection you're talking about but the later bikes like your's uses Deutsch connectors. They are better than the ones Harley used previously. If you crimped the pins on and didn't get it right, that may be your problem. If the connection is inside the turn signal itself, you may need new signals. I have a '94 model FXDWG and they all work great even after all these years. If you could be more specific about the problem, I may can help you a bit more.

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No turning signals


Turn Signal Lamps
The turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL, CORN LPS Fuse. Battery voltage is then applied through the TURN SIGNAL, CORN LPS fuse circuit to the hazard warning switch. The hazard switch supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the body control module (BCM) . The front turn lamps are grounded at G101. The rear turn lamps are grounded at G301 and G302.
Turn Signal Lamps and/or Indicators Inoperative

2

  1. Turn the ignition switch to the ON position.
  2. Place the turn signal switch in the LH and RH on position.
Do the turn signals operate properly?
Go to Testing for Intermittent Conditions and Poor Connections yes
Go to Step 3 no

3

Are all of the turn signal lamps and indicators inoperative?
Go to Step 5 yes
Go to Step 4 no

4

Are only the turn signal indicators inoperative?
Go to Step 16 yes
Go to Step 9 no

5

Check the TURN SIGNALS CORN LPS fuse for an open.
Is the TURN SIGNALS CORN LPS fuse open?
Go to Step 25 yes
Go to Step 6 no

6

  1. Disconnect the hazard switch.
  2. Turn the ignition to the ON position, with the engine OFF.
  3. Connect a test lamp between the ignition positive 1 voltage circuit of the hazard switch and a good ground.
Does the test lamp illuminate?
Go to Step 7 yes
Go to Step 27 no

7

Connect a test lamp between the ignition 1 positive supply voltage circuit of the hazard switch and the ground circuit of the hazard switch .
Does the test lamp illuminate?
Go to Step 8 yes
Go to Step 23 no

8

  1. Install a fused jumper between the ignition 1 positive voltage circuit of the hazard switch and the turn signal flasher signal circuit of the hazard switch.
  2. Place the turn signal switch in the RH on position and the LH on position.
Do the turn signal lamps illuminate?
Go to Step 17 yes
Go to Step 15 no

9

Is a front turn signal inoperative?
Go to Step 10 yes
Go to Step 13 no

10

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative front turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative front turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14 yes
Go to Step 11 no

11

  1. Disconnect the body control module (BCM) connector.
  2. Connect a test lamp between ground and the front turn signal switch signal circuit of the BCM.
  3. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 12
Go to Step 22

12

Test for an open or for a high resistance in the supply voltage circuit of the inoperative front turn signal lamp. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 21

13

  1. Turn the ignition switch to the ON position.
  2. Disconnect the inoperative rear turn signal lamp.
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal lamp and a good ground.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 14
Go to Step 28

14

Connect a test lamp between the ground circuit of the inoperative turn signal lamp and supply voltage circuit of the inoperative turn signal lamp.
Does the test lamp illuminate?
Go to Step 20
Go to Step 26

15

Test for an open or high resistance in the turn signal flasher signal circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 18

16

  1. Turn OFF the ignition.
  2. Disconnect the instrument panel cluster (IPC).
  3. Connect a test lamp between the supply voltage circuit of the inoperative turn signal indicator and the instrument panel cluster (IPC) ground circuit.
  4. Place the turn signal switch in the appropriate ON position.
Does the test lamp flash ON and OFF?
Go to Step 19
Go to Step 24

17

Inspect for poor connections at the harness connector of the hazard switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 30

18

Inspect for poor connections at the turn signal switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 29

19

Inspect for poor connections at the instrument panel cluster (IPC). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 31

20

Inspect for poor connections at the inoperative turn signal lamp. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 34
Go to Step 32

Sep 05, 2015 | 2001 Oldsmobile Intrigue

1 Answer

Deuce turn signal not working


Possible fault with the switching unit. Please check the line to the switcher unit from the hand control switch and if this is good then the switcher is faulty , if not the cluster switch at the hand control can be faulty.

Jun 07, 2012 | 2000 Harley Davidson XL Sportster 883

1 Answer

There is a fault with my Samsung LE32R41BD HDMI port which needs replacing. I have tried two different connectors and two different HD boxes without receiving a full HD signal. Can I order a replacement...


Basically, it's a very poor design fault by Samsung. There is no support for the HDMI connector inside the TV - it is simply held in place by the surface mount solder connections. If you connect/disconnect a few times, the solder joints will crack and you lose full signal transmission across the connector as the joints gradually fracture one by one. The only fix is to completely remove the connector from the PCB, clean the solder joints and replace the connector. You should also add screw holes to secure the connector (that's the bit that Samsung forgot!) to the casing and add suitable screws.

Aug 13, 2010 | Televison & Video

1 Answer

2001 hd softail deuce. shut off on me going 70mph


Hi Firebug72, and the usual suspects are:
1. Severely discharged or damaged battery.
2. Loose, corroded or broken battery cable.
3. Alternator not charging or below normal rates.
4. Failed ignition coil, ignition/electronic module.
5. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor.
6. Faulty ignition switch.
7. Water or dirt in fuel system, carburetor or filter.
8. Fuel tank vent system plugged or gas cap not venting.
9. Fuel tank empty.
10. Fuel valve vacuum line broken or carburator vent line closed off.
11. Restricted, blocked or kinked fuel line.
12. Failed fuel pump, pressure regulator and or fuel injectors.
For a prime suspect please visit website below. Good luck and have nice day.
Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

May 29, 2010 | Harley Davidson FXSTD Softail Duece...

1 Answer

Lits horn but will not start


dose it turn over? if not sounds like a problem with starter solinoid attach jumper to + term. other end touch to starter main wire see if starter turns

Apr 09, 2010 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

My harley davidson 2001 sportster will not start. We charged the battery to 100%. it makes a horrible noise when you go to start it. What is it?


Check your all the fuse. Check battery connectors. Check your battery with volt meter. If your battery is old, depending of your mileage it needs replacement But first check if its still charging. You have to fully charge your battery in order for a kick start of your hd 2001. Hope this help you out.

Apr 04, 2010 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

How to lower stock shocks on my 2001 harley davidson deuce?


(Rear) The HD "Softail" (R) system has some adjustment to preset the load level of the shocks (not much). You will need to have a "pre-load" wrench to make adjustments to the system. Your custom option ($$$) would be to install an aftermarket kit that can both lower the bike, and some provide adjust-ability via an on-board air compressor. Both "Legend," and "Progressive" make such kits, but they are costly and are best installed professionally. (Front) There are lowering kits which replace fork springs and reset the front stance of a bike, but these may also affect handling and safety so be careful. Actually lowering bikes is an art, since ground clearance is changed and you might encounter cornering issues.

Mar 14, 2010 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

Front L/R turn signal lights remain on.


bad ground or check the bulbs mack sure none are blown.

Aug 04, 2009 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

Left turn signal not working


check for a break in the signal wire from the switch,if none then check the switch,they have been known to go bad

Jul 01, 2009 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

1 Answer

Need to remove full time power to turn signal lamp for Euro compl


Their are 6 HD dealers in Sweden, I would contact the nearest dealer and ask them what you need to do. I'm pretty sure it is some type of relay that needs to be changed.

Apr 28, 2009 | 2001 Harley Davidson FXSTD - FXSTDI Deuce

Not finding what you are looking for?
2001 Harley Davidson FXSTD - FXSTDI Deuce Logo

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...