Question about 2003 TM Racing MX 125

1 Answer

How do i adjust the hydrolic clutch on a 2003 tm 125

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 188 Answers

Normally there is no adjustment of a hydraulic clutch. The slave cylinder is driven the same distance each time the master cylinder is actuated by the clutch lever. Unless you have low fluid, I expect your clutch is slipping due to wear or weak springs or possibly due to additives that should not be used with a wet-plate clutch running in engine oil. Check your owners manual for oil recommendations to make sure you have suitable oil for your bike.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tm 125 engine casing removal


Witch casing? Clutch casing ; Remove any levers cables lines or kicks that maybe in the way, drain oil then remove the casing bolts tap lightly with rubber hammer or block of wood to free it up and slide off.

Feb 21, 2012 | 2003 TM Racing MX 125

1 Answer

Hi im looking for clutch plates and basket that will suit a 02 tm 125 mx and want to know how much this will cost.


Clutch plates vary in price, but if i remember correctly, the TM uses the same as the KX and CR models. Last set i bought cost us 30 pounds. Baskets again vary, best to do a web search but your looking in the region of 100 - 200 pounds for a good one.

Mista B.

Jul 10, 2010 | 2002 TM Racing MX 125

1 Answer

Suzuki 125 intruder clutch adjustment


You'll need to adjust this by the adjuster right on the lever assembly itself.

Apr 11, 2010 | 2003 Suzuki VL 125 Intruder LC

1 Answer

91 SUZUKI RM 125 CLUTCH PROBLEM


First, try the cable adjustment at the lever end, if no more movement re-adjust inwards, then adjust at the clutch end.
If no joy, then it is either the lifter mechanism or the clutch its self.
Ride Safe
Bike-Doc

Please mark this as useful (if it has been!!)

Aug 03, 2009 | 2003 Suzuki RM 125

1 Answer

How do i adjust my clutch


There is no other standard adjustment. You could install heavier clutch springs but about all that is going to do is make the clutch lever stiffer. You should adjust the clutch handle for about 1/4" of end play.

A “very helpful” rating for this answer? Thanks!

Jun 13, 2009 | 2003 Suzuki RM 125

2 Answers

Diffrences betweein oils


your bike does not use tranny oil.only motor oil.your gears are lubricated by your motor oil as well as your clutch.it works by a sump system.I use yamahlube for my bike.

Apr 20, 2009 | 2003 Yamaha YZ 125

1 Answer

My 1986 kx 125 clutch does not engage worked prior


possible the cable is needing to be adjusted make sure it is pulling on the pivot

Apr 15, 2009 | 2003 kawasaki KX 125

3 Answers

I have 2003 kawasaki kx 125 when you put it in gear with clutch in it jumps forward and dies. where do i start with this?


make sure clutch ,is disengaging properly when you pull in clutch lever,adjust lever until you have about 1/8" freeplay.if still not disengaging, you need to drain gearbox oil, take clutch cover off & inspect clutch pack, you may have friction plates sticking together.

Feb 18, 2009 | 2003 kawasaki KX 125

1 Answer

Clutch slipping on 2004 350z roadster


This is a Hydrolic System ,thus there is no Adjustment for what you discribe, You will need a New Clutch Assemble. I Recomend replacing ALL Clutch Parts while Trans is out. Uncluding All the Parts Listed Reliece Bearing, Clutch Disc, Pressure plate,And Renew Slave Cylinder FLUID.

Jan 24, 2009 | 2003 Nissan 350Z

2 Answers

2003 KX125 Clutch Problem


the clutch springs may be weak check the specs you may just have to change them

Jan 15, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
2003 TM Racing MX 125 Logo

347 people viewed this question

Ask a Question

Usually answered in minutes!

Top TM Racing Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

JOHN LAPIER

Level 3 Expert

2422 Answers

Gregg Mahin
Gregg Mahin

Level 3 Expert

40013 Answers

Are you a TM Racing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...