Question about 2006 Yamaha DT 125 X

1 Answer

Play in the pistonor also called piston slapping and when changing down gears in high revs from 3rd to 2nd it doesnt select and from 2nd to 1st

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,167 Answers

Hi buddy strip the cylinder off and inspect the small end bearing which part is moving up and down the conrod or piston and get back to me bud

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A MICRA 2005 MODEL WITH NO POWER. WHEN THE CAR IS IN NEUTRAL CAR REVS FINE, THE MOMENT YOU SELECT 1ST GEAR ENGINE LABOURS AND REVS UP VERY SLOWLY AND DOESNT REV PASED 4000 RPM PLEASE ADVISE


possible selector problem when you push forward for 1st your are actually pushing into 3rd, try starting car from 2nd gear and see if it stalls as that would mean you are hitting 4th. usually a car can pull off in second gear ok. if this is the case go to a dealer to sort this out. as your gear selector is not aligning up correctly. if this is not the case the engine could be losing compression but that seems less likely.

Oct 22, 2014 | 2005 Nissan Micra Visia

2 Answers

2007 mustang gt have engine knock problem when going from 1st to 2nd gear at 5000 rpms?


5.000rpm's high revs and you run into problems with valve bounce ( hitting pistons) ,ring slap, gudgeon pin knock, big end noise and possible main bearing noise . You may also be getting a hydraulic lock in the hydraulic followers that is holding the valves open too long. Unless the engine has been specifically built for these rpm's any loose ,worn on unsuitable part will cause problems I am thinking that you have around 100.000 miles on the clock after 7 years and the motor is not young Ford V8 engines specifically built for a 500 klm race are limited to 5.500 rpms because they destroy the timing chain if driven over that speed .

Jun 03, 2014 | 2007 Ford Mustang GT

1 Answer

Gears rev to high when changing


try changing your gearbox oil

Nov 26, 2013 | 1995 Toyota Camry

1 Answer

2006 dodge carrivan stuck in 3rd high revs


I don't know what 80kl is. Are you saying the trans is in 3rd gear pulling out and no 1st or 2nd? Or it setting still and in 3rd. Engine RPM going up....I don't follow you?

Feb 11, 2013 | 2006 Dodge Grand Caravan

1 Answer

A problem with my VW Golf mk4 2.3 V5 auto gear selection. Hi all, ive got a mk 4 golf 2.3 v5 auto, the gear transition between 2nd and 3rd is playing up. When the car is cold it will either make the...


hi, i would like to warn u that i had this issue with the same car, eventually the gear box stopped going above 2nd gear ,would not change up even in semi manual,i was told i needed new gear box,had a recon box fitted, but now the garage says i need a new computer cause it not communicating with the gear box properly,cost so far 1200 pound + what ever computer cost, fingers crossed this works

Oct 12, 2012 | Cars & Trucks

1 Answer

Toyota high rev problems


Sounds like a Throttle position Sensor.
Not an expensive part.

Jul 12, 2012 | 2008 Toyota Corolla

1 Answer

My 2001 GMC Jimmy 4x4 Automatic with 84K miles. It winds when I put it in reverse and I think I only have 1st and 2nd gear. Additionally it revs high, like over 3000 rpm, delays and then eventually...


It winds up in 1st and then shifts right from 1st into 3rd. Then never shifts into 4th. Plus rev is gone. You broke the sun shell. The transmission will need to rebuilt or replaced.

Oct 30, 2010 | 2001 GMC Jimmy

1 Answer

My z32 takes so long to change from 1st to 2nd. is this a prolem with these autos, or is mine just playing up? wants to change at about 6000-6300rpm but doesnt change till just over 7000rpm, and sometimes...


check the rubber vacumn pipe connection ends from the inlet manifold to the valve on the gearbox ,its losing vacumn so the valve isnt changing the gears for you ,simple job to do

Sep 17, 2010 | 1989 Nissan 300ZX

1 Answer

My '01 Mustang V6 revs high when in neutral/when changing gears.


sounds more like the IAC, Idle air control valve.. they can be cleaned with carb and choke cleaner gently...

Nov 17, 2008 | 2001 Ford Mustang

Not finding what you are looking for?
2006 Yamaha DT 125 X Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...