Question about 2003 Yamaha WR 250 F

1 Answer

My wr 250 will sputter after it starts and i have to stay on the throttle back and forth to keep it running, When i take off its fine through all gears but as soon as i let off the gas it dies.....plus now carb leaks out two tubes even with gas valve off

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,167 Answers

Ok buddy the problem is the float is too low so take the carb off then unscrew the bolts on th bottom 2-4 holding the bowl on the pull it off watching the seal once its off you will see the float you need to slide the pivot pin out holding it in with a small pin and just push it through then take the float out with the inlet fuel valve still connected take the fuel valve off and bend the tab the valve connects onto bend it up wards a little bit only a tiny bit if to much then it wont allow fuel back in then reinstall it and get back to me bud My wr 250 will sputter after it starts and i have - 9ef9ffe.jpg
2c14a6d.jpg

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motor starts fine runs for five minutes then dies starts back up back up fine but no throttle response after thatfine.


if there is electronic throttle then probably needs replacement, get second hand one , or otherwise can try to take it out and clean it, if there is an access to electronic part of it try it open carefully and clean contacts with some alcohol, sometimes it helps

Apr 16, 2014 | Cars & Trucks

1 Answer

We have a 1987 Ford Econoline RV ... It starts fine but will only idle for 20-30 seconds.. When we put it in drive it sputters and quits... It also sputters and quits while idling...


Can you pump the gas pedal or spray carb cleaner into the throttle body to keep it running ?
Have you checked fuel pressure with a gauge ?

Jun 29, 2013 | Cars & Trucks

1 Answer

1991 Nissan maxima hesitates


Best guess is O2 sensor is reading too much unburned fue in the exhaust for some reason and leaning out the fuel flow to compensate. Runs when you throw more throttle at it but leans out as you try to hold steady speed. Should throw a code though.

Apr 25, 2013 | 1991 Nissan Maxima

2 Answers

1981 Honda CX500D keeps stalling


Unlikely to be a starter motor try changing your spark plugs and checking battery. Hope this helps.

Oct 19, 2012 | Motorcycles

1 Answer

After running for awhile the engine begins sputtering and dies out. I generally have to keep it a full throttle to keep it running. I tried spraying down the carb with cleaner which allowed me to run with...


always check spark and compression first spark needs to be blue and compression should be 120 but will barely run on 80psi if both are fine rebuild and acid dip carb the adjustment is 2 full turns out

May 19, 2012 | Briggs & Stratton Briggs Stratton Intek V...

1 Answer

Well the motor locked up and i couldnt kick it at all shifted threw all the gears just fine but i wuz messing with it and i ran through all the gears trying to turn the back wheel and knock it loose didnt...


If you are running 5th gear mid throttle the compression in the motor wasnt enough to push the piston back down

for the record ( i run a ts 250 savage 2 stroke ) i,ve done it my self it happends

try to keep it the power band you will be fine

good luck.

Mar 26, 2011 | 2004 Suzuki RM-Z 250

1 Answer

At full speed in 5th gear on my 1990 YZ 250 WR (wide ratio) the rear wheel locked up. I turned off the engine. I was able to start the engine again on the 1st kick. I was able to ride back to camp in 5th...


Hi, Rvptough for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Dirt Rider Magazine
1997 yz 250 Shifting Problem Yamaha 2 Stroke
YAMAHA YZ250 LC Owner Service Manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

Oct 18, 2010 | Yamaha YZ 250 Motorcycles

1 Answer

New top end but no compression or very little


Sounds like you have the crank to cam timing incorrect.  Also you may have the valves set too tight.  Dose it pop and sputter?

Mar 22, 2009 | 2005 Yamaha WR 250 F

1 Answer

Hesitation problems 2003 yamaha wr 450 f


sounds like a jetting issue. change the main jets starting from the largest one you own and work your way down.

Dec 14, 2008 | 2003 Yamaha WR 450 F

Not finding what you are looking for?
2003 Yamaha WR 250 F Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...