Question about 2008 Yamaha YZF-R6

1 Answer

Just buy r6 2008 engine running ok but when i put 1st gear the engine plze help

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 269 Answers

Just check to make sure you have the kickstand all the way up before putting it into gear. Also check the switch on the sidestand too.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 a4 w0nt select 1st gear or 2nd or reverse with engine runnin bu


SMELLS LIKE SOMETHING NEEDS TO BE CHANGED AND THAT IS PROBABLY THE CLUNCH!!

Feb 23, 2014 | Audi A4 Cars & Trucks

1 Answer

1995 Ford Bronco engine dies when shifted into drive but runs in reverse or 1st gear


Could be fuel filter,air filter,tune up,wires,coils.low idle too low.

Jun 13, 2013 | 1995 Ford Bronco

1 Answer

Problems selecting 1st gear peugeot 106 1.1 zest


If the clutch is a problem you will have difficulty selecting 1st only as the gears would be spinning from the engine revs.. I would say that the front input shaft (clutch shaft) bearing is failing allowing miss alignment of the synchros and not allowing proper engagement of the gears synchro rings. It means removal and repair to the gear box so the clutch can be inspected while the box is out.

Apr 08, 2013 | Cars & Trucks

1 Answer

1999 honda civic lx and engine running but wont move when put into gear


indicates a problem clutch master cylinder or failing clutch cable which ever your car has
take it to a clutch and brake specialist for a proper diagnosis and quote
the fix is a new clutch master cylinder or clutch cable

Dec 08, 2017 | Honda Accord Cars & Trucks

1 Answer

VEHICLE DRIVES ON 1ST GEAR ONLY WHEN PUT ON DRIVE.


van wouldn't drive at all if transmission needed replaced. my opinion, get it to a trans shop, let them be the judge, its free !!!!!!!!! just do it donot exceed 25 MPH. good luck

Feb 02, 2013 | 2003 Dodge Caravan

1 Answer

Shuts down when put in 1st gear


Most likely the safety switch for the kickstand - it's supposed to kill the engine if the kickstand is down nd you put the bike in gear. That switch could be faulty or a wiring issue with it. Use a meter to check the switch.

Aug 21, 2012 | 2000 Suzuki VL 1500 Intruder LC

1 Answer

He put it in D or R and it still in Neutral, raving the engine doesn't help. After several tries, and usually like ~5 minute warmup if finally gets in D and then the car drives perfectly fine. It only...


First doublecheck your transmission fluid level. Its the red handled dipstick near the back of the motor. You check trans fluid level WHILE ENGINE IS RUNNING. If that is ok, you might be getting towards the end of that trannys life. My mother had a bonninville, for the last 2 years we had to drop it down to 1st (the 1 on the gear shift) then into drive. This worked for a couple years before it finally blew out. Try going from 1st then into "D" and make sure it shifts, You can always shift it manually from 1st to 2nd to 3rd to drive if needed. Aint gunna hurt anything, just dont go over 3-4 on you tachometer. You dont wanna redline it.

Jan 31, 2011 | 1995 Buick Regal

1 Answer

I bought a 1999 jetta volkswagon for my 15 year old son turning 16 next month. The previous owners put a used engine (2000) with 63,000 miles. the car itself has 180,000. I have no problems ******* from 3,...


When you install an engine, you don't "line up" gears. It's likely that either you have a worn shift fork or synchro (both inside the transmission).

Jul 08, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
2008 Yamaha YZF-R6 Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...