Question about Yamaha FZ 600 Motorcycles

2 Answers

My 2006 fz6 idles at 1120 to 1200 rpm is this the right idle rpm

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

Ironmike_926 wrote: no it should be anywhere from 600 to 900

Absolute rubbish!! The idle speed should be between 1250 and 1350 rpm. If the engine is cold, the EFi will raise the idle speed temporarily to about 1600 rpm until it warms up (usually within 5 to 10 minutes at a standstill).

Your idle speed of 1120 to 1200 rpm is absolutely fine. However, if it drops any lower, you can raise the rpm by playing with the idle speed adjuster screw located on the gear-side under the fuel tank (can be seen without having to remove the fuel tank). Turn clockwise to increase rpm. You will find details on how to do this by selecting your manual from this link:

http://www.yamaha-motor.co.uk/community/service/manuals.jsp

WARNING: if the idle rpm continues to drop, you may have a more serious issue with the valve clearances, air-filter, or spark plugs. Consult a technical book (such as Haynes), or take it to your local Yamaha dealer to get it serviced.

Posted on Dec 11, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 128 Answers

No it should be anywhere from 600 to 900

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 E250 rough idle


Sounds like air filter box cover not on right, will cause this problem and check all connections to throttle body if no secure or lose will cause same problem.

Jun 12, 2014 | 2006 Ford E-250 Extended

1 Answer

What should a 2005 or 2006 Maserati QP idle at with AC off?


depending on engine fitted. around 900 rpm some are 850 rpm but it really depends on on what you want, high idle uses more fuel. if the engine keeps cutting out at idle it may be the idle valve needs to be clean'd and depending on the engine type depends on what is fitted to the engine.

Nov 25, 2013 | Cars & Trucks

1 Answer

Yamaha 125 ttr idles to slow


Hi, Anonymous the carburetor throttle shaft wheel has two cables the cable closest to the right side of the bike is the throttle cable and the one closest to the left side is the idle cable. Right about the middle between the two is the idle adjustment bolt it faces out towards the air filter end of the carb. The engine should be at operating temperature with the enrichener off to set the idle between 950-1050 rpm. Turn the idle adjustment bolt clockwise to increases idle speed and counterclockwise to decrease idle speed. If you have access to your air fuel mixture bolt you may adjust it as well if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air fuel mixture bolt clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back it out 2 full turns to establish a starting point start the engine and check the idle rpm's and adjust the idle adjustment bolt accordingly for 950-1050 rpm if necessary, adjust the air fuel mixture bolt 1/4 turn at a time and let the engine settle for about 10 seconds, clockwise for a leaner mixture and counterclockwise for a richer mixture you are seeking the highest rpm your air fuel mixture bolt can acquire without going past 3 full turns from bottom then readjusting the idle adjustment bolt back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture bolt all the way in then your pilot/low-speed jet is too big. Final adjustment should be made with a clean air filter mounted to the carburetor. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have wonderful a day.
Other Yamaha TTR 125 4T carb help
how to set idle up on ttr125 Texas Offroad Network Forums
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
YAMAHA TT R110E Owner Manual

Jul 20, 2012 | 2006 Yamaha TTR 125 E

1 Answer

2006 envoy at idle of 500 rpm, voltage meter shows low charging, air conditioner quits cooling, lights dim. is the alternator bad?


This is too low an idle speed, it should be around 620 RPM. You probably need to have the throttle body cleaned.

Oct 20, 2011 | 2006 GMC Envoy

2 Answers

2006 AUDI A4 2.0 HAS A HIGH PITCH SQUEAL AT IDLE TAPERS OFF AT HIGHER RPM -THEN MAKES A WHINING NOISE WHEN ENGINE IS SHUT OFF --ANY IDEAS?


hey not sure if its totally right but the high pitch squeal at when its idleing could be the tentioner pulley bearings on the engine belt not sure about the whining noise when its shut off

Oct 04, 2009 | 2006 Audi A4

1 Answer

I have a 2006 Suzuki GS500F. At stops it


possibly needs a carb clean, but sounds more like it needs a valve adjustment.

Sep 24, 2009 | 2006 Suzuki GS 500 F

1 Answer

I have a 2006 PT Cruiser. When starting in the


If you go to advance auto they will scan the car for free. if you write the codes down and update your question it will be easier to eliminate some of the sensors.

Jun 30, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Hummer h2 idle rpm too low


I can't solve the problem but was hoping you found the answer. I have a 2003 Hummer H2 and I am having the same problems if started in park or Neutral it will idle fine but if I put it in drive or reverse it will not idle

Did you find the solution and if so could you email me the fix.

tdunham@drainageplus.com

Thanks,

Troy

May 28, 2009 | 2006 Hummer H2

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

607 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...