Question about 2000 Husqvarna TE 610

1 Answer

Carburation Adjustment - 2000 Husqvarna TE 610

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

Screw in all the way gentley as not to destroy the pointed tip, then I usually turn out three full turns, then adjust as engine is running.

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ryobi problems


Yes sir it is. You need to adjust the carburetor. Unless you have an adjustment tool you'll have to take it somewhere to have this done.

Jul 16, 2014 | Ryobi Garden

2 Answers

GOVERNOR ADJUSTMENT ON A FHV 500 17 HP KAWAQSAKI ENGINE


adjusting the govenoris something you want to take to a trained tech NO AFFENCE;trust me I am a tech.

Oct 26, 2012 | kawasaki (kawasaki)

1 Answer

I have a sym 100 Euro jet that will not start in the cold


if real cold wheather the oil is thick and will make starting sluggish, or not at all.
it takes alot of cold cranking amps to start a cold motor. you could probably jump start it with a battery charger that has 50 amp start option.

if you think its carburation.........your automatic/manual choke may not be working, check cable adjustment, and lubricate your cables.
you can pull the choke out and clean it.

Dec 08, 2010 | Sym Husky 125 Motorcycles

1 Answer

Backfiring on decelaration


there r 2 types of backfire-intake relating to valves n timing and exhaust-unburned fuel either way--ajust these causes and chec out carburation also

May 09, 2010 | 2003 kawasaki VN 750 Vulcan

1 Answer

Carburation & emission control?


check for broken or disconnected vacuum hose/line
also check for the fast idle sped control valve for defect

Mar 18, 2010 | 1983 Honda Accord

1 Answer

I have a 94 cr 125 , that i just bought , it started at the guys house but now wont start for me , tried putting a new plug in , any ideas


Try a compression test first see what it is, next check for spark, remove plug from engine leave connected, ground the end of the plug to the engine and kick over, if you have good compression and spark, it is in the carburation, some bikes dont start well when cold due to bad carburation(air leaks, bad jets etc)you could try roll starting down hill and see if it starts.

Nov 07, 2009 | 2002 Honda CR 125 R

1 Answer

Carburation for road racing


buy a dyno jet kit from dyno jet should make some diffrance

Oct 29, 2009 | 1993 Honda CBR 250 RR

1 Answer

My Poulan chainsaw is hard to start and will not re-start once it is warm. Any suggestions besides junk it.


Spend $ 40 for a tune up at a local chainsaw seller/mechanic. Most Stihl outlets are very good. It sounds like carburation needs adjustment, but they also do a good visual inspection. Mine get done about every 3 years worth of use. HTH
Lou

Sep 29, 2009 | Poulan Pro 42CC 2 Cycle Chainsaw, 18"

2 Answers

Fuel lines rotted replaced them. carburation is off how do i reajust the carburator it has two small ajustments side by side and one large ajustment above it i think the one large one is the idle screw i...


large adjustment is the idle
if it is a zama carb then 1 turn out each
if it is a walbro carb. 1and1/4 out each
preliminary adjstments they will have to be tweeked after its running or maybe not

Jun 10, 2009 | Craftsman Garden

1 Answer

Chain saw starts then dies shortly after


hi

I think you have a carburation problem.Carefully disassembly the carb and clean it.Check the fuel line and filter,the ventil of the gas tank.

regards savumihai71

Nov 24, 2008 | Garden

Not finding what you are looking for?
2000 Husqvarna TE 610 Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...