- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
http://www.ebay.ie/itm/SUZUKI-GSX-R-1100-GSXR1100-SLINGSHOT-1989-1992-PETROL-TAP-REPAIR-KIT-/281347814373?pt=LH_DefaultDomain_3&hash=item4181a2f3e5 or try here http://www.wemoto.com/bikes/suzuki/gsxr_1100_l_gv73b_slingshot/90/.
Have you turned the fuel tap on (If it has one)? As far as I can remember, there are only 2 lines ( Feed and Return) check that the one with the filter in it is going to the "fuel in" line on the carbs.
There should only be two pipes as the primer is located in the carb, the fuel hose from the tank with the filter on the end goes to the carb connection nearest the alloy pump cover held with a single screw, the other pipe fits to the other car connection and goes back to the tank, it just pushes into the tank to return the fuel. the fuel hoses are clear and you can watch the fuel movment, push the primer in and fuel returns to tank, let it out and fuel is drawn into the carb, if the hoses are connected correctly
Properly relieve the fuel system pressure, as outlined earlier in this
Raise and safely support the vehicle.
Observe all applicable safety precautions when working around
gasoline. Do not allow fuel spray or fuel vapors to come in contact with a spark
or open flame. Keep a dry chemical (Class B) fire extinguisher near the work
area. Never drain or store fuel in an open container due to the possibility of
fire or explosion.
Use a suitable hand operated pump device to drain the fuel through the
filler tube into an approved container.
Before disconnecting any fuel lines from the fuel tank, thoroughly clean
around all hose connections.
Disconnect the fuel filler vent hose from the fuel tank.
Detach the fuel filler hose from the fuel filler inlet tube on the fuel
tank. Position the hose out of the way.
Disconnect the vapor hose from the front of the fuel tank.
Detach the fuel return pipe and position the hose out of the way.
Disconnect the two rear rubber exhaust hangers from the rear of the exhaust
system and allow the exhaust system to hang down slightly.
Unfasten the exhaust shield mounting bolts, then remove the exhaust shield.
Support the fuel tank with a suitable jack.
Remove the two bolts securing the fuel tank straps, then swing the straps
out of the way.
Lower the fuel tank enough to disconnect the vapor hose from the fuel sender
assembly and the vapor hose from the vapor pipe at the rear of the fuel tank.
Detach the electrical connector from the fuel sender assembly and remove the
two retaining clips.
Remove the tank from the vehicle, slowly to ensure all connections and hoses
have been disconnected.
Clean all parts well. Inspect the tank for dents, rust or other damage. On
high-mileage vehicles, it may be good practice to remove the fuel pump module
and replace the flexible strainer on the fuel pump.
Position the fuel tank under the vehicle and raise the tank with a suitable
Connect the vapor hose to the fuel tank at the vapor pipe at the rear of the
tank and connect the vapor hose to the sender assembly.
Attach the electrical connector to the fuel sender assembly.
Connect the fuel feed and return lines to the sender assembly.
Raise the tank into position into the vehicle and swing the mounting straps
under the tank.
Install the front fuel tank strap mounting bolts and tighten to 35 ft. lbs.
Remove the jack.
Connect the fuel return pipe to the fuel feed pipe.
Attach the rear fuel feed pipe to the inlet side of the fuel filter.
Tighten the line fittings to 16 ft. lbs. (22 Nm). Make sure to use a back-up
wrench to prevent the fuel filter from turning.
Connect the vapor hose to the vapor pipe at the front of the vehicle.
Attach the fuel filler vent hose to the tank. Connect the fuel filler hose
to the fuel filler neck of the tank.
Install the exhaust heat shield and the mounting bolts.
Position the exhaust system and install the rubber hangers.
Carefully lower the vehicle, then refill the fuel system
Connect the negative battery cable, then install the fuel filler cap, if not
Turn the ignition switchONfor 2 seconds, OFF for 10 seconds,
thenONand check for fuel leaks.