Question about 2006 Harley Davidson XL 1200 C Sportster Custom

2 Answers

Turn signals dont work and niether does the horn or brake light

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The acc fuse will be toast they on a 15amp. youll have one spare on the bike. change the fuse and your off.

Posted on Nov 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 142 Answers

I had same thing,electrical wiring,must go to shop

Posted on Oct 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signals,horn and brake lights dont work harley dyna


Hi Anonymous, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose.
Check the wire connections to the horn making sure they are clean and tight, there is power going to it and the ground wire is securely fastened. Then look behind the horn body for a small set screw sometimes with a jam nut. This screw puts tension on the horn diaphram to vibrate alot or vibrate a little. Have someone hold in the horn button while you adjust the screw in or out as necessary. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. For a free wiring diagram please visit the website below and good luck:
Harley Davidson Wiring Diagrams and Schematics

Mar 27, 2012 | 2000 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

I have a 1990 Mercury Cougar. Several problems...Blinkers, hazards, horn, and break lights are not working. However the break light in the back window comes on when the break is pressed. Checked fused and...


I am unaware of what a "CO" display is.
Now with the blinkers, hazard, horn and brake lights not working that may be the multi funtion switch (blinker switch) that is located inside the column (where the blinker lever attaches).
Obviously the blinker, hazard and horn will all work off of something in the column. Brake lights, you may think a switch on the pedal.

the brake lights do work with that switch but when you have the kind of tail lights where a turn signal light shares the same bulb as a brake light, the brake light is cancelled for the turn signal by running through the multi function switch inside the column.
The third brake light does not blink so its not on that same circuit.

Oct 07, 2011 | 1990 Mercury Cougar

1 Answer

Got a 2000 hayabusa, instrument panel back brake light and turn signals out, replaced 15amp fuse, rode the bike next morning same again?


Well...in general....the turn signals brake lights and horn and instrument lights are typically on the Signal fuse on most bikes.
So....any recently added accessories to the circuit?
If not...start at the signal and brake light sockets...inspect wiring around the socket and the sockets themselves looking for a possible short.
Then check wiring to the back under seat for chafing pinching etc
Inspect the wiring aroiund the steering head in case a pinch has occured causing a short on bar rotation.
If all looks okay...inspect the horns....not sure on your Busa, but many horns use 2 wires and ground through the horn button....so the horn needs to be insulated on its mount so as it may be wired hot and can short.

Apr 01, 2011 | 2000 Suzuki GSX 1300 R Hayabusa

1 Answer

Turn Signal Issues HELP!!!


turn signal switch in steering coulum is bad

Jun 09, 2010 | 1992 Cadillac DeVille

1 Answer

Brake lights,turn signal and horn not working...


Check the wiring within the headlight shell--look for connectors that may be corroded or pulled loose. A little WD-40 will favor connection integrity when sprayed into the connectors, then coupling and uncoupling them several times. Hope this helps!

May 24, 2010 | 2000 Harley Davidson FLHTCUI Electra Glide...

Not finding what you are looking for?
2006 Harley Davidson XL 1200 C Sportster Custom Logo

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...