Question about 2004 Husqvarna TE 250

1 Answer

Having problems kicking her over takes 12 or more kicks why wont she start of first 2 kicks

Posted by on

  • scottleonard Oct 03, 2009

    just put new iridium one in was better with standard ngk it a kick start conversion just doesnt have enough in the kick to get going i think

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,167 Answers

Have you tried a different plug get back to me

Posted on Oct 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is my Yamaha Banshee is hard to start


It looks like your compression is too low (worn rings from dusted motor) Push starting spins the motor faster than kick starting and when hot the rings expand just enough to seal off. Before kicking a cold motor try putting in a squirt or two of engine oil in the plug hole to see if there is a difference.

Apr 26, 2013 | New Ray Ray 1/12 Yamaha YF 350Z Banshee 06

1 Answer

Bike wont kick start or idle , it will coast


first drain the carby, then set your air mixture screw 2 turns out, from the fully turned in position. The starting proceedure is as follows, when the engine is COLD, turn on fuel, pull on the choke fully, and kick the engine over. DO NOT use any throttle, when the engine is cold, and the choke is on. Remember Choke on, NO throttle.
When warm, no choke, and a little throttle when kicking.

May 12, 2010 | 2003 kawasaki KX 125

1 Answer

My py 90 wont start,


the same problem happened my py90 try taking out the sparkplug blowing in the hole to clean it out and if that doesnt work blow into the petrol cap really fast wen ur finished blowing put ur finger over the cap dont let any air out then kick start it about 6 times it should work on 2 kick starts but keep ur finger over the petrol cap

Feb 13, 2010 | 2005 Factory bike Chrono SM 250

1 Answer

Starting problems


Well its cranking so not the starter and its got the juice so not the battery maybe. Check to see if its got the correct voltage to kick it over. Could be a fuel problem replace plugs wires and fuel filter. Also check you oil level maybe its low and wont start bc its low. I think it has a oil level sensor that may prevent it from turning over.

Aug 31, 2009 | 2002 Lincoln LS

1 Answer

I have an old moped. IT's a simple 2 stroke with a


What do you mean
"wont kick start with battery" ?

Is the starter turning the motor ?
If not - the starter could be stuck..
WHILE tring to start it with starter - give the actual starter a smack with a wrench..

Rate well ;o)

Jul 22, 2009 | 1979 Honda CBX

2 Answers

Starting my Mojave 250


check comprsion. check valve clearance.

Apr 26, 2009 | kawasaki Full Suspension Mountain Bike Men

3 Answers

Yz 250 wont kickstart


Hi!
You obviously look after your machine and very sensible when laying up, however as you are probably aware 2 strokes rely heavily on compression, A. to produce excellent combustion and B. to draw fuel into the chamber. So when you try kick starting you can't get enough revolutions to draw the correct amount of fuel into the cylinder, where as you push start you constantly turn over the engine increasing compression slightly and bingo it fires.
Can you remember how when kick starting it before this problem the feel on resistance when kicking over? has it now become a lot easier? if so you possibly have worn or broken compression piston rings.
A compression test will reveal this, I hope this sorts your query?
Press the Blue button please for my FREE effort,
Thank You!
Paul 'W' U.K.

Feb 06, 2009 | 2000 Yamaha DT 125 R

1 Answer

2001 nissan quest,air conditioning


I hope you are adding R134a & not R-12. I think you are just confusing them.
our problem is a leak in your a/c system somewhere. Your a/c should cycle about 4 times/minute. When you add refrigerant, you are refilling the system and making it work again. The system only holds about 3 cans of refrigerant. If you are doing yourself, get a fill hose with a gauge on it so you can see if it's "ok" low or high pressure.
The leak will probably require pro ehlp.

Jul 17, 2008 | 2001 Nissan Quest

Not finding what you are looking for?
2004 Husqvarna TE 250 Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

choprboz5

Level 2 Expert

196 Answers

Joseph Hoffmann

Level 3 Expert

1706 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...