Question about 2006 kawasaki ZX-10R

1 Answer

How to mount 06 zx10r framesliders? Do i need to take fairings off or cut? Thought it would be just sliders themselves instead got sliders, brackets and a lot of screws....??? They are PSR (Powerstands) framesliders. Thanks.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

They should have included instructions. i am not familiar with that model but most frame sliders have brackets that bolt to the engine/frame mount on each side. then the slider mounts to the newly installed bracket. you Will have to modify (cut) holes in the body for the sliders to protrude. they would not serve any purpose bolted to just the body in the event of a crash.
Use a torque wrench for this as those bolts also will be holding your engine. you may get lucky and the not have to modify the body if they designed the slider to protrude through existing body holes.

Posted on Oct 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 electra glide front faring removal


1993/1994 Outer Fairing and Windshield for FLHTC, and FLHTC ULTRA

Removal

First remove the headlight assembly and the bolts, nut and the washers attaching the outer fairing piece to the windshield and inner fairing piece. THEN loosen the four bolts attaching the light bracket and the outer fairing piece to the fork brackets. Remove the upper bolts but leave the lower ones in place. Cover the fender. THEN rest the lower light bracket onto the fender. THEN remove the fastener securing the headlamp trim ring and remove the trim ring. THEN remove five screws that secure then headlamp assembly to the outer fairing and remove the headlamp assembly. THEN reach through the headlamp opening and loosen four locknuts on the two studs on each side of the headlight area which attach the fairing to the metal brackets inside the fairing. THEN remove the fairing by pulling it straight ahead away from the brackets.

Installation

First loosely position the outer fairing in place over the inner faring with the four studs going into the two brackets. Then install the five windshield fasteners through the outer fairing, the windshield and the inner fairing. THEN tighten the four stud nuts to secure the fairing to the brackets, being sure to have the inner and the outer fairing properly aligned at their outside edges. THEN position the light bracket so that the slots fit around the upper fork bracket bolts and thenalign the lower fork bracket mounting holes and replace the two lowering fairing mounting bolts through the light bracket and the outer fairing and the inner fairing and screw them into the lower fork bracket. THEN make sure that the rubber seal around the inner fairing is properly seated and not pinched and tighten the four fairing attachment bolts to 12-13 foot pounds (16 -19 Nm). THEN tighten the windshield screws to 4 inch pounds (0.45 Nm) but no more than this amount starting in the middle and working outwards on both sides. THEN reinstall the headlight assembly.

Jun 03, 2014 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Replace front pads transit 2008


a fairly simple job but there are a few points to cover to do the job properly. No1 DONT buy cheap pads. They will throw black dust everywhere, they do not dissipate heat well and will damage your rotors which are more expensive than pads. Also you can feel the difference, the more expensive pads do stop better but they also help you apply a more progressive and even pressure resulting in smoother braking. Once you have the vehicle off the ground and safely secure with the wheels off, you will notice the 'caliper' can be removed from the mounting bracket by removing the bolts (13mm or 1/2")from the 'sliders' (located on the top left and right). You must hold the large inside bolt (near the dust rubber) with a large spanner (17mm or 3/4") Pry the caliper from the rotor and mounting bracket. Pull the slider pins from the mounting bracket, clean and re-grease slider pin and guide hole and replace using high temp grease. Check condition of all dust rubbers and seals, (there should be no sign of leaking fluid or holes where dust can enter), clean dirt from the the tin angle pad anti-rattle guides. Push the caliper pistons all the way in using an old pad and a 'G' clamp or similar. To make the job very professional there is a silicon type substance that can be applied to the pistons where they contact the new pads, this will stop 'pad rattle and squeal', but is not totally necessary. Position the new pads in the bracket against the rotor, put the caliper in place and replace the slider retaining bolts remembering to stop the inner bolt from turning. Pump the brake pedal to push the pads against the rotors and replace the wheels. With any brake work always test drive, Before moving off make sure pedal is high and hard, move a little and ease the brakes to ensure they stop without making any nasty sound. Stop the car 2 or 3 times from a 'walking pace' and if all is good continue to 'bed' the brakes in by doing several light stops from a low speed (speed limit). Congrats! Job well done!

Feb 10, 2014 | Transmission & Drivetrain for Ford Transit...

1 Answer

I own a 2006 zx10r iwant to use a 2008 side mount exhaust preferably a gp slip on will it work or what has to be changed?


You can buy a m4 go style exhaust for the 06-07 on ebay for a pretty good price. Lots of exhaust manufacturers make this type of exhaust. As for the 2008, the mid pipe won't work and you would have to make your own or have one custom built. Also the 08 header is different.

Jun 03, 2012 | 2006 kawasaki ZX-10R

2 Answers

I ahve a 2009 kawasaki zx10r and there is a sound at 4000rpm i think it a vibration but i can't find it


there is a metal bracket that vibraites on the inside of the headlight fairing below windsceen i stuck foam betwen bracket and fairing and it went away.

May 20, 2010 | Motorcycles

5 Answers

I get excessive vibration in my 06 Street Glide fairing at idle.


I have a 2007 street glid eand have been through 2 sets of fairing brackets. it started with around 500 miles on the bike. very bad design, I had the factory bracket reinforced and problem solved. My old mans bike, same problem. Check the fairing brackets,

Dec 30, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Front motor mount on 1993 camry 4 cylinder


The mount is probably bad anyhow. so get it out however you need to, you can always cut the nut or bolt off and the new mount will have a new stud. so you will only need a nut.

Sep 23, 2009 | 1992 Toyota Camry V6

2 Answers

2005 kawasaki zx10r ninja. Need to change spark plugs. have got 1 & 4 out but struggling with 2 & 3. do i need a special tool or lower engine


the tool kit with the bike should be good enough,no need to lower the engine, to make things easier when you get them undone find a piece of rubber hose that fits over the sparkplug and use it to pull the plugs out and install them ...then tighten them with the plug tool.

Jun 03, 2009 | 2005 kawasaki ZX-10R

3 Answers

Engine swap 04 zx10r on a 06 zx 636 f


The frame mounting points are completely different. A zx 636 frame wraps around the motor where as a zx10r frame goes directly over the motor. That's how they keep the zx10r nimble enough to feel like a 600cc sport bike. But in this day and age if you have enough time and money you can accomplish anything. Honestly it's just easier to sell your 6 and buy a 1 liter.

May 31, 2009 | 2006 kawasaki ZZR 600

1 Answer

Need installation instructions for the spacemaker GE microwave oven model JVM164owj01


Here is the link to the installation manual. Cut and paste on the address bar of your browser. http://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-40409-1.PDF It is possible to do it by yourself, but its a royal pain in the a**, so have someone available to help you lift it into place and hold it while you get the screws into the cabinet above. You could use sheet rock anchors to put the mounting bracket on the back wall, but I would really suggest getting the mounting screw into wall studs instead, even if you have to drill a hole or two through the mounting bracket.

Apr 04, 2009 | GE Spacemaker JVM1640SJ Microwave Oven

Not finding what you are looking for?
2006 kawasaki ZX-10R Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...