Question about 1976 Honda CB 100

1 Answer

I have a 100cc Lifan 4 stroke its a chinesse made honda the problem is it runs fine and everything when i start to go the sprocket spins but the wheel will not move? i need help can i weld the sprocket to make it stay on rim so it will make the rim move?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 79 Answers

I would.

Posted on Oct 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a two stroke 100cc motor on go do I start no pull cord just clutch

place the back of the cart on blocks , switch on the ignition and spin the rear wheel.
leave the clutch engaged
both wheels will have to be off the ground

Sep 05, 2015 | Motorcycles

1 Answer

I have a ram 100cc quad was working fine but run

hi if you ran the motor out of two stroke oil you have done serious damage to the engine ie:piston&rings the bore possible bearing damage as well might be cheaper to get another motor good luck

Sep 14, 2014 | Motorcycles

1 Answer

Speedfight 2 2 or 4 stroke

if prior to 2006 it is a two stroke

Mar 13, 2014 | Craftsman Garden

1 Answer

Peugeot speedfight 2 100cc 4 stroke

not sure type of carb it has, but sounds like it has a float and the float is stuck open so the needle won't seat and stop the gas flow
the float could be stuck open or the float may have a pin hole and the float is filling with fuel holding it open that will make you have to start it with full throtle and most of the time they won't run at and idle, it floods out and will stall

Mar 08, 2014 | Craftsman Garden

1 Answer


If your bike is 4 stroke then it will be the valves need adjusting,this is the usual problem for hard starting . 999pounds 50cc lifan on the road 3yr warranty

Nov 12, 2013 | Honda Motorcycles

1 Answer

My bike not show gair lightes

Hello i have a Lifan Mirage 125cc 4 stroke does anyone know how to de restrict them at all many thanks


Mar 07, 2013 | 2006 Honda ANF125 Innova

1 Answer

What is spark plug gap on 4 stroke 70cc engine?

The Honda CRF100F 2003-2005 has a 100cc engine and uses a spark plug gap of .7 mm.

The Honda CRF70F 2003-2005 has a 70cc engine and uses a spark plug gap of .7 mm.

Sep 09, 2011 | 2005 Honda CRF 100 F

2 Answers

How do i derestrict my lifan s-ray 50cc 4-stroke scooter please? forgot to add its a honda based engine and its a 59 plate thanks

Unless you find a small "restricting washer" between the head and the exhaust pipe...Then usually there is no easy means. In the past these "washers" were put in place to reduce performance, the idea was as the riders skills improve the washer can be removed. It also was a way for parents to keep their children from zooming flat out everywhere.

Dec 03, 2009 | 2006 Honda ANF125 Innova

Not finding what you are looking for?
1976 Honda CB 100 Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers


Level 3 Expert

79186 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides