Question about Honda CBR 1000 RR Fireblade Motorcycles

1 Answer

Hi my rr08 had the clutch recall fitted four months ago. sume 800klm later it has started with a vibration that go´s when the clutch lever is plulled. after three returns to Honda´s shop and the old clutch reinstalled it still have the vibration fron 4.5k revs up. can anyone say what needs to be done the cure it? many thanks in advance Ivan

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 79 Answers

It's pu tof ballance somehow. Try a different shop. If they can't get it right in 4 try's, never go there again.

Posted on Oct 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I had a new clutch a year ago. a month ago a new clutch master cylinder was fitted.


Check the fluid in trans it might be bad could also be through out bearing

Oct 13, 2015 | Cars & Trucks

1 Answer

2003 Scenic 1.9DCI, new clutch, slave flywheel fitted 18 months ago after clutch failure. Last month pedal went flat to the floor and unable to put into gear. Bled system, car ok for a couple of days then...


There are only a few places air can get in the master cylinder and connections the pipe going to concentric slave the connections to slave or slave itself

Feb 05, 2015 | Cars & Trucks

1 Answer

Engine runs hot, causes vibrations, hesitates on acceleration


Hi, Constanti627 and the usual suspects are:
1. Fuel octane rating too low.
2. Faulty spark plugs.
3. Incorrect spark plugs for the kind of service.
4. Excessive carbon deposits on the piston head or in the combustion chamber.
5. Ignition timing advanced or retarded due to faulty sensor inputs (MAP, CKP, CMP)
6. Engine overheating due to lack of lubrication or coolant.
For more specific information about your issue please visit the website below. Good luck and have a nice day.
DOWNLOAD Bajaj Pulsar 180

Apr 02, 2012 | 2005 Bajaj Pulsar 180

1 Answer

I have put new bearings in steering and wheels if I pull the cluch in and rev the eng the vibration is in time with the engin I have done the eng mounts


Hi,
If you are getting a vibration through the clutch lever when you pull the clutch in then this is a sign that your clutch plate has an uneven spot on it and will need to be replaced.
One way to check this is to get someone to engage the clutch lever and look at the clutch lever on the gearbox housing. If you see the pivot arm moving in and out then you have a surface problem on your clutch assembly.
Hope this helps.
Thanks
Jason

Jul 19, 2011 | 2001 Yamaha V Star 1100 Classic

1 Answer

Hallo Polo 1.6i classic Need help with my clutch , did fit an new clutch kit , fly wheel was skim , and all the seals was replaced , a month after , it started slipping again , the fit new kabel self...


hi,at the side of the gearbox there is a green round cover when it is removed there is a fork like lever there they normally brake or it can be faulty clutch parts that is fitted.hope it is usefull

May 19, 2011 | Volkswagen Polo Cars & Trucks

1 Answer

How 2 adust clutch ,bike stalls when dropped into gear ,shift is quite clunky


The old design of slave cylinder (fitted to 2001 and prior bikes) wears badly leading to the unit drawing air in and ultimately loss of clutch action. A new seal usually cures things but the housing itself can wear too, so this might also need to be replaced. Alternatively the later, improved slave cylinder can be fitted, but this necessitates fitting of the later (longer) clutch pushrod. Or, try one of the many "LARGE" piston type slave cylinders that are available. These reduce the lever pressure by approx 30%.
Bleeding process is:
  • bleed valve closed
  • squeeze clutch
  • open bleed valve - clutch lever will come in to bar - hold it!
  • close bleed valve
  • release clutch
repeat till there are no more bubbles and operation is restored.


Jul 01, 2009 | 2001 Ducati 750 SS i.e. N-C

1 Answer

Kick start is jammed


Put the bike in 3rd, 4th or 5th gear, the higher the better. Sit on the bike, with your hand off the clutch lever, and rock the bike back and forth to rotate the clutch hub. This might free up the lever. You will need to drain the oil and remove the right side casing to see and service the kick starter. If I recall correctly, there is a spring clip that allows the kick gear to engage the clutch hub. The piece could be broken, weak or out of position.

Please rate this answer. Thanks Shay!

Apr 06, 2009 | 2002 KTM SX 250

1 Answer

Clutch


Check to make sure the slave and master cylinders are working. You can probably bleed it if the slave cylinder started leaking. Could possibly be internal on the clutch master.

Mar 06, 2009 | 1988 Honda VF 750 C Super magna

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...