Question about KTM 625 SMC Motorcycles

1 Answer

Trying to bleed clutch ktm 625 smc - 625 SMC KTM Motorcycles

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

They can be a pain.......the best way to do so without a vacuum bleeder is to back fill it. buy a oil ratio syringe from walmart or an auto parts store. attach a short vinyl tube to it and **** it full of fluid. now remove reservoir cap and attach syringe to the slave cylinder. open bleed bolt and back fill slowly....tighten bleeder and work clutch to check for pressure and unsure there's no air.



Posted on Oct 03, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi I have a 2006 ktm 625 sxc when I pull clutch in bike is still pulling and pressure as gone from lever any ideas would b great thank you

sound to me like the clutch slave cylinder. follow the pipework down from the bars to the casing. Unbolt the slave cylinder and im guessing it will be covered in break fluid. new slave cylinder is the answer hope this helps

Feb 17, 2015 | KTM Motorcycles

1 Answer

How do you remove the spark plug cap. I have applied a little pressure but I dont want to damage anything.

IF you mean the metal barrel that threads onto the end of the plug:
Remove spark plug, hold by the hex with a wrench, and grab the barrel with a pair of pliers and unscrew.

May 11, 2014 | 2005 KTM 625 SMC

1 Answer

2004 ktm 625 smc lc4 black recidues on my dadiator cap(i dont think is oil cause is not white and the water is clean.)and i just flush the radiator(how is the best way to flush my radiator??? thank a...

add 1 teaspoon of washing powder . ie, daz or persil. run the bike for about 10 mins let it cool down then flush with clean water. refill with pro cool or 50 50 mix of anti freeze and water. cheers kev.

Jul 06, 2010 | 2004 KTM 625 SMC

1 Answer

I got a 2004 625 ktm smc lc4 is a nice bike. but

Dont stress. A LITLLE more than the level is nothing to worry about. Keep the oil level between the 2 marks when the engine is cold and you'll be fine. Best way is bottom level is for cold. Oil must be above this level when cold. Top level is for warm. Oil must be below this level when hot.

Jul 02, 2010 | 2004 KTM 625 SMC

1 Answer

Would too much oil in case make oil leak on 2004

All engines have a oil level .if too much oil is put in an engine ,above the recomended level then pressure produced when the engine is running will force ouil into places its not meant to go .This will cause oil leaks in any number of places and could cause damage to seals or correct running of the engine .

Mar 12, 2010 | 2004 KTM 625 SMC

1 Answer

I have a ktm 300 2008 modle i was riding it round then had no clatch do i need to bleed it?

hi mate when you pull the clutch lever in if it goes all the way in to your grip then it needs bleeding if it gets tight then you have a problem with your clutch itself also if bleed the clutch doesnt work then it could be your seals gone in the reservoir /the piston

Aug 27, 2009 | 2005 KTM EXC 300

1 Answer

KTM LC4 625

Hi and welcome to FixYa,

It would seem you posted twice, pls try here, here or here. In some, the wiring diagram is part of the Service Manual. If the year is different, most harness/wiring would be relatively similar.

Good luck and Thank you for using FixYa. Happy Holidays.

Dec 14, 2008 | 2002 KTM LC4 625 Sc

2 Answers

Clutch fluid

Use 5wt. fork oil or ATF Dextron II/III. I've use both and have the 5wt. fork oil in now. Suppose to have a lighter pull but can't really tell any difference. Use a large syringe to pump the oil in from the bleeder at the bottom up to the master cylinder.

Nov 10, 2008 | 2005 KTM 625 SXC

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

593 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts


Level 3 Expert

79865 Answers


Level 2 Expert

342 Answers

Steve Banks

Level 2 Expert

232 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides