Question about 2008 Triumph Daytona 675

1 Answer

2008 triumph daytona

Starts and runs when the clutch is pulled an is in neutral but if i put it in gear it shuts off. an ideas???

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 376 Answers

The switch for your kickstand mybe disconected. Or do you have the kickstand down.

Posted on Sep 30, 2009

  • thomas67516 Oct 09, 2010

    the kickstand has a neotral safe switch on it if it is broken it might be telling the computer that the bike still has the stand down

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Triumph trident 93 model side stand works as it should but warning stays on with stand up john


Hi, John either the switch is faulty or the circuit is grounded to the light that being said the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Side stand bypass
Sidestand Clutch Safety switch issues
Triumph TROPHE Service Manual Page 2
http://www.triumphestore.com/
http://mybikemanuals.com/triumph/uncategorized-triumph-owners-manuals

May 09, 2017 | 1993 Triumph Trident 900

1 Answer

2008 Triumph Street Triple won't start


Hi, Cbitt331 before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
ST3R won start HELP
What to do When Your Motorcycle Won Start
Triumph DAYTONA 675 Service Manual
http://www.triumphestore.com/
Triumph Daytona 675 Owner Handbook Manual

Jun 16, 2017 | 2008 Triumph Street triple

1 Answer

1995 Triumph Thunderbird cuts out the instant I put it in 1st gear


Hi, Drmwvr2 and the usual suspects are:
1. Faulty wiring to any safety switch.
2. Safety switches loose at the mounting point.
3. Faulty kickstand safety switch.
4. Failed kickstand safety switch circuit diode.
5. Stretched side stand spring.
6. Side stand not coming up far enough to disengage switch.
7. Faulty clutch lever safety switch.
8. Faulty neutral safety switch.
9. Clutch not properly adjusted.
10. Clutch plates sticking, forward lurch
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Dies when put in gear
stalls when engage into gear Problem Solving Tech Forums Messageboard...
Triumph Thunderbird Service Manual
http://www.bikebandit.com/oem-parts/1995-triumph-thunderbird/o/m147385
Triumph Thunderbird Owner Manual

Jul 23, 2017 | 1995 Triumph Triumph Thunderbird

1 Answer

Triumph Daytona 600 will not turn over


Hi, Jordan_x_tur before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Bike won start Not battery think
04 Daytona 600 Won start please help
Triumph 2003 Daytona 600 Service Manual
Hermys Tire Cycle Inc 2004 Triumph Genuine Tools and manuals Motorcycle...
Triumph Daytona 600 Owner Handbook Manual

Jul 04, 2017 | Triumph Daytona 600 Motorcycles

1 Answer

2004 Triumph daytona 955i. 4000 miles. Was riding and all of a sudden bike dies, no power to lights speedo or any gauges, starter button wouldnt work. Pushed home and turned key on all lights worked and...


Hi, The_redneckc and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or better and be able to pass a proper "LOAD" test if necessary your battery may show 12.5 volts or more but have little or zero amps and must be replaced.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Fuel tank empty.
10. Fuel tank contaminated with ethanol sludge.
11. Water or dirt in the fuel system, or clogged filter.
12. Restricted, blocked or kinked fuel line.
13. Faulty fuel pump.
14. Faulty pressure regulator.
15. Faulty or clogged fuel injectors.
For more information about your issue and valuable "FREE" downloads that you need please click on the blue links below. Good luck and have a wonderful day.
2002 955i Daytona Quits while running and then will not start
Topic Starting Issue on 2005 Triumph Daytona 955I RUNNING AGAIN Read 8197...
Triumph Daytona 955i 2002 Service Manual
Hermys Triumph Motorcycle Parts 2004 Triumph Genuine Body and frame...
Triumph Daytona 955i Handbook

Apr 17, 2017 | 2004 Triumph Daytona 955i

1 Answer

Have to hold clutch to keep bike from dieing


clutch plate adjusment or cable adjustment, it sounds like the clutch is staying engaged, try loosening the cable on the clutch until there is lots of slack init and try to start the bike, if it jerks forward then you are going to have to adjust/replace the internal clutch plates hope this helps

dan

Mar 11, 2010 | 2004 Triumph Daytona 600

1 Answer

Where can I find an exploded diagram of the rear spindle of my daytona 600, to show me what spacers go where. After having a rear tyre replaced, I now have a knocking sound, but only when using throttle,...


If it goes away when you pull the clutch in then I would think it something to do with the engine but i could be wrong there. Can you put the bike on a jack and put it in gear and maybe find out what going on. Let me know what you find out. You got me wondering.

Oct 03, 2009 | 2003 Triumph Daytona 600

1 Answer

Clutch slips


Hello, wheelies mm not good for your gearbox or clutch, 1st off is the gearbox working OK, does it jump out of 2nd gear under hard acceleration? then we can move on from this point,
Ian

May 26, 2009 | 2004 Triumph Daytona 600

Not finding what you are looking for?
2008 Triumph Daytona 675 Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...