Question about 1988 Yamaha TZR 250

1 Answer

Wiring head lights to my 1988 blaster. but i made a new kill switch.so the high and low beems for the lights are not connected i just want a constant power to the lights when the blaster is started which wire would give me a constant?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

One of the small wires comming off the ignition coil should do that.

Posted on Oct 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 colorado head lights do not work low or high beems


check the light control module
check/ replace head light switch

Dec 13, 2015 | 2006 Chevrolet Colorado Crew

1 Answer

Head lights do not come on changed switch fues is new high beems work when u pull back on switch


Do the flashers work?

My '87's headlights would not work for some reason. And I noticed that the flashers did not work, and the flasher button did not flash. Upon replacing the fuses for the flashers, they worked fine.

Jul 05, 2011 | 1988 Volkswagen Cabriolet

1 Answer

The headlight on the pass. side works right. the drivers side when in low beem, the light is in high beem. when the light is on high beem the light is on low beem. this is a 2000 mercury sable


someone has switched the wiring harness sockets to the wrong bulbs or installed the bulbs in reverse. get in behind the headlight assembly on the driver side and reverse the wires, if that does not work then pull the bulbs and swap them inside to outside and vice versa.

Jun 10, 2011 | Mercury Sable Cars & Trucks

1 Answer

1998 Camry Low beams work fine but when i switch to high beam i loose all lights


the relay for your highbeem lights is bad, replace it and you should be good, or you could just switch the high beem relay, with the low beem relay, they are the same, and if the high beems work like that you know its full proof, if not... well you know, we will hafta move to something else.. hope you find this helpful

Dec 04, 2010 | 1998 Toyota Camry

1 Answer

2005 Trailblazer, Low beems will not work high beems do


Pull plastic cover off of column ck where wires mate to multi function switch and switch for traces of heat . More than likely switch is bad.

Jun 16, 2009 | 2005 Chevrolet Trailblazer Ext

2 Answers

Fuse is fine hazards work but turn signals do not. all new bulbs.


your flasher is probably bad, it is usely round and mounted close to the fuse box

May 02, 2009 | 1988 Chevrolet Beretta

2 Answers

1996 ford ranger headlights not working


It's the dimmer switch in the column.

Jan 06, 2009 | 1996 Ford Ranger SuperCab

1 Answer

L head light low beem not working


You probably have the low side of your bulb blown check the bulb if that dont fix it ck your conector.if your dimmer switch was bad it wouldnt work on eather side. I will try to get you a diagram for the fuse box. PHIL.

Jan 06, 2009 | 2003 Ford Explorer

1 Answer

Head Lights


check the continuity of the headlights to make sure there switching from the DTR Lights to the highbeams. If you are not getting the proper continuity check the ground wire for the low beams to ensure its properly grounded and has proper continuity throughout the wire. If not replace the wire or tighten as required and that should fix your problem.


lemme know if you require further assistance,

thanks - Nate

Aug 13, 2008 | 1996 Chevrolet Cavalier

2 Answers

Ford ranger headlights


check your head light switch

May 25, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
1988 Yamaha TZR 250 Logo

Related Topics:

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...