Question about 1986 kawasaki GPz 1000 RX

1 Answer

I need the torque settings for the clutch spring bolts on a gpz 1000rx

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 302 Answers

A service manual is a valuable tool with an aging bike. I suggest the dealer/mfr. or Clymer books. In the meantime, go to the library reference section...646 stacks should have what you need.

Posted on Oct 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is torque setting for clutch springs?


Hi Mick:
Don't know what your bike is so suggest you refer to you make and model service manual.
Example - My KLR 650
Clutch hub nut - 100 ft-lb
Clutch spring bolts - 87 in-lb

Oct 18, 2015 | Motorcycles

Tip

Gpz 1000rx Engine dies on pull away.


my gpz 1000rx 1986 would start and rev fine but die on pull away, for weeks tried allsorts (carbs cleaned, plugs changed etc) Solution for me was WD40 the sidestand switch and tighten earth lead from battery where it bolts to engine block, now its fine. Hope this helps WAZZA

on Oct 22, 2013 | 1986 kawasaki GPz 1000 RX

1 Answer

86 gpz 1000rx starts and runs well but dies when letting clutch out, new plugs and clean carbs.


I would check the safety switches are working properly, particularly the side-stand switch. On many bikes, the engine will die when you let the clutch out if you have the side stand down.

Oct 19, 2013 | 1999 Bimota SB8R

1 Answer

How to set up a new clutch


There is no setting the tension on the springs if the clutch has 4-6 springs as most do. The bolts that hold the clutch springs in tighten all the way down until they are snug (I would say about 100 inch-lbs max for each bolt torque.

Jul 18, 2012 | Honda Motorcycles

1 Answer

What is the torch on my springs on my clutch for my fz1000


Hi, a typical torque setting for a six mm bolt is 6 to 8 foot pounds, however care must be taken as the clutch posts are quite easily stripped of their threads, because the bolt is pulling a spring you may get a false sense of torque, tighten the bolt until the washer meets the post and give a little more tension on the bolt, would probably try on a 6 mm bolt elswere on the bike other than the clutch to get a feel for the small amount of torque

Sep 08, 2011 | Yamaha FZR 1000 Motorcycles

1 Answer

Do you need a special key to change out the clutch


no buddy its simply the covers off clutch.spring bolts undone,springs come out,pressure plate then will pull off and the plates will slide off and thats it but what you will require is a torque wrench to torque the clutch spring bolts up after any more info needed get back to me buddy

Nov 01, 2009 | 2003 Yamaha YZ 250

1 Answer

What is the torque for the bolts that hold the clutch spring plate reduced effort clutch spring on a 2003 FLSTIC msd2455@yahoo.com


I've never really torqued these bolts and I've replaced plenty of the diaphragm springs. Usually I put stronger springs in the clutch since I'm building up the horsepower of the engines. I put a drop of Loctite 242 (med, strength blue) and tighten the bolts to about 25-30 foot pounds. Check the standard torque for a grade five bolt of the size that are in the clutch.

Oct 27, 2009 | 2003 Harley Davidson FLSTCI Heritage ...

1 Answer

I need proper torque specs for clutch relese springs 84 gpz 1100


You are over torquing the springs. Buy a generic manual from your automotive shop. ZX11 specs are much higher than the GPZ.

Aug 20, 2009 | 1995 kawasaki GPZ 1100

2 Answers

Kawasaki 87 stickers


RdDecals.com in Canada has complete sets or individual sticker pairs including pinstripes for the US Ninja version, but not the GPZ. So, with one of these kits, you could get all of the right stickers except the GPZ (comes with Ninja) stickers on the upper cowl, and the 1000RX for the belly pan (comes with 1000R). They have stickers for other older Kawasaki's as well.

May 26, 2009 | 1987 kawasaki GPz 1000 RX

Not finding what you are looking for?
1986 kawasaki GPz 1000 RX Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...