Question about 2002 Harley Davidson FLHR - FLHRCI Road king

3 Answers

This morning I ran over what sounded like a flat piece of plastic. It sounded like a piece of the plastic "popped" up and struck my bike 02 Roadking around the front or the Rh side...around the air cleaner. I'm not really sure. I can't find any obvious damage to the metal or wiring. However, my bike will not start. It turns over but there is no spark. Please help. Thanks

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 269 Answers

Check the wires from the crank position sensor.

Posted on Sep 28, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 355 Answers

Well check all fuse first then check wires to coile and see if you have volts on one of the wires it should be at least 12 volts the on the right side of bike right about were foot floor board is that round cap buy the foot is where ignition module is there should be little wire harness coming out of there that harness runs long frame may have Ben hit damaged wire in it look under floor broad and foll the wire to see if damaged hope this helps

Posted on Sep 28, 2009

Testimonial: "Very helpful. Will leave more feedback if this is the problem. Thanks for you help, Redoil."

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

The Problem I am having is that when you accellerate the bike acts like it wants to die, but than picks up like nothing happened. when you slow down it acts like it is only firing on one cylinder just about dieing. This is on a 2002 Harley Davidson FLHRCI Road King.

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear fender off 2000 roadking fit a 2003 roadking


Hi Anonymous, my guess is probably with minor modifications if any maybe. The 03 fender would fit a 01 and 02. The 2000 would fit a 99 Good luck

Apr 03, 2014 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

02 roadking surges and stalls


You do not say when it surges or stalls. You should first see how the power commander is progarmmed as it may have a problem for the mapping of a certain rpm range etc.

Jul 11, 2012 | 2002 Harley Davidson FLHRCI Road King...

1 Answer

Hi im new to road bikes....im wondering is 53,000 kilometers alot for my bike its a gsxr 600 2002 model...


if the bike was well maintained 53,000 km is not high for an 02. my 06 Roadking has 57,000 km.

Sep 12, 2011 | 2002 Suzuki GSX-R 600

1 Answer

I Have a 2005 Yamaha V Star 650 Motorcycle-bike just stopped running (60 mph) , would not restart. Battery good, fuel full, spark at plug any idea's to troubleshoot?


Try tapping on your fuel pump with a plastic hammer with the ignition switched on. Or bypassing the fuel pump completely with a piece of fuel line. It sounds like you ran out of gas which is related to the fuel petcock position or a non-functioning fuel pump.

Aug 27, 2010 | 2005 Yamaha V Star 1100 Classic

1 Answer

How do I remove the handlebars on a 1998 HD roadking


Remove the cap in the center of the handlebars and take a look, I'm afraid you will have to take the whole housing assembly apart. It's been a few years since I did ours.
Not so easy, first the head light has to come out, the a 5/16 nut inside the head light housing holding on the trim piece that needs to come off. One that's off the plastic trim piece on ignition need to be pried off "gently", then remove the 2 screws and that cover will come off giving you access to the handle bar mounts. Unscrew the old ones at the headstock and put the new ones on where the old ones went and screw them in at the right spot (where you want them) sit on the bike and hang on to them and do them up "tight". Hope this helps! Good luck!

Feb 22, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

When I was driving to work this morning a ran over plastic


not if you got there without any changes to your normal traveling happenings. i doubt if you have anything to worry about ... happy xmas

Dec 08, 2009 | Hyundai Motor 2003 Elantra

1 Answer

1994 FLHR RoadKing, 1340cc, engine miss


this is going to sound weird but if your bike has a crankshaft location sensor it is a litte one screw held on wired sensor up by your oil filter that connects to your regulator on front of bike it cuts power to your coil and ecm if it cant read right had same problem on my bike ran like a champ after that

Apr 26, 2009 | Harley Davidson 1994 Harley-davidson...

1 Answer

Bike just dead over night


Have you checked the battery and cables ?

Nov 16, 2008 | 2006 Aprilia RS 125

1 Answer

AOC lm929 monitor


AOC LM929 or Envision EN-7100 removal instructions:

DANGER!!! UNPLUG and allow the monitor to discharge before servicing.

with a small flat head screwdriver, insert into the edge and pop open the small plastic

pieces that surround where the stand connects to the monitor. put plastic pieces aside.

lay monitor on soft flat surface front side DOWN. with a phillips head screwdriver,

remove 4 screws in the center that hold on the stand. put stand and screws aside.

lay monitor on soft flat surface front side UP. insert flat head screwdriver into the

side edge of the grey plastic and turn screw driver so the plastic surrounding the

screen edge pops up exposing an area surrounding the screen. put plastic rectangle

piece aside.

slide out plastic buttons piece from the side and put aside.

with a phillips head screwdriver, remove 8 screws (4 on top and 4 on bottom) that hold

the screen assembly to the back housing. now lift screen assembly out of the plastic

housing. put back plastic housing and screws aside AND lay the monitor screen with the

FRONT side down on a flat soft surface.

with a phillips head screwdriver, remove 2 screws that hold on the metal electronics

cover. slide the cover down and remove. put the cover and screws aside.

USE CAUTION!!! Some components may still contain a charge.

check fuse... whatever...

Aug 29, 2008 | Computers & Internet

Not finding what you are looking for?
2002 Harley Davidson FLHR - FLHRCI Road king Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...