Question about 1999 Honda XR 250 R

1 Answer

Starter problem my XR250 starter keeps on running when engine was running.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 376 Answers

The bendix on the starter is not retracting so I am thinking that the return spring went bad. Remove the starter and bench test it and see if it returns. If it does not than you will have to have it rebuilt or get a new one.

Posted on Sep 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1999 the engine keeps just shut off while driving down the road the engine keeps turning but wont crank I put some engine starter in the carb.and it tried to start.could it be the fuel pump


if it was the fuel pump engine should start with starter spray at least for a second or two, so, it sounds like your fuel pump is bad.
turn ignition to run and try hearing the pump run.

Dec 17, 2014 | Cars & Trucks

2 Answers

Engin keep turning when hand is off the key


You need a new ignition switch. Check with Autozone or OReilly's.

Dec 14, 2013 | 2006 Pontiac GTO

1 Answer

I just replaced my starter on my 99 gmc yukon and it was fine for 10 minutes then it made this weired noise and when I went to turn the truck off the engine kept going and then smoke came from the starter...


Sounds to me like your starter did not disengage and was running the whole time when vehicle running. From your key to the starter is a "trigger wire" which activates the starter when you turn the key. If that wire end touches other wires on the starter then the solenoid will stay on keeping the starter running which will then over heat and burn out the starter. If vehicle was running fine before the starter replacement there is really nothing else it could be.

Dec 03, 2013 | Cars & Trucks

1 Answer

When i try to start the engine it won't start, but the starter keeps running.


Yes starter is spinning but it has to be engaged.Its not engaging.The problem is with starter system.Get the flywheel checked.
Its suggested to get the starter system removed and checked. If all checked ok,then it can be fuel or ignition issue.

Click the link below To Troubleshoot the problem:-
http://autopartsdiagrams.blogspot.com/2013/09/engine-it-wont-start-but-starter-keeps.html


--------
This will help.
Thanks./

Sep 22, 2013 | 2005 Chevrolet Colorado

1 Answer

1999 range rover 4.6she starter keeps running


Just changed mine for the same problem!!! replaced starter, problem solved! Unusual design by american standard, for the main motor to continue to drive, !?

Jan 29, 2013 | 1999 Land Rover Range Rover

1 Answer

Doesn't want to keep running and some grinding noise when startin


From what you describe I would suspect that the starter is not fully engaging. I'm assuming that the grinding noise you hear when you try to engage the starter is INSTEAD of the engine cranking. If I assumed wrong, ignore the following:
Pull the starter, check the flywheel for excessively worn areas. Most of the time the flywheel is ok, it's just the starter. Any time you disassemble a starter you should replace the bushings and brushes. Never remove the starter with the battery still connected. Remove the negative terminal from the battery before you attempt to remove the starter.

Jun 06, 2010 | 1986 Jeep Cherokee

1 Answer

1990 300zx solenoid/starter relay


I would go for the starter motor personally first, as thats the part that cranks the engine over :)

that gets power, then it starts turning the flywheel, the starter motor also keeps the engine running inbetween the engines power strokes while its running.

Go for the starter relay & the starter motor :)

Thanks.

Apr 10, 2009 | 1990 Nissan 300ZX

1 Answer

After motor work starter runs when power applied


sounds like starter solenoid is staying energized sending continued power to starter. need to make sure you plugged the right wire from the starter button and not another hot wire w/ fulltime hot. also if thats ok need to test for power turning off to solenoid when releasing button. if thats ok try tapping on solenoid. lastly, make sure your positive cable from battery is hooked to starter solenoid, then another hot cable(longer) hooks from solenoid to starter, if you hook long hot cable directly from starter to battery, starter will continueous spin.

Feb 19, 2009 | 1996 Honda VT 1100 C Shadow Spirit

Not finding what you are looking for?
1999 Honda XR 250 R Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...