Question about 1982 Suzuki GS 650 GT

1 Answer

Valve are off how do i adjust them - 1982 Suzuki GS 650 GT

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 986 Answers

You should get a manual for the bike. Below is a linkto a GS website where you can get alot of information.

http://www.thegsresources.com/gs_links.htm

The valve job is a good size job.
Remove the gas tank
remove the valve cover
adjust the vavles.

This is where you need the book you should check valve timeing and engine timing while at this step.

Best of luck

Posted on Sep 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Civic EX, valves became noisy at60K, valves quiet after warmup. They will probably still be noisy after I adjust them. Would the cause be excessive wear on the valves stem ends and rockers?


If there were no wear, the valves wouldn't need adjusting. The reason for periodically adjusting the valves is to compensate for the wear that the valve train undergoes over the life of the engine. Be optimistic! Have confidence that adjusting the valves will reduce the noisy valves.

Apr 10, 2017 | Cars & Trucks

1 Answer

What is the clearance between the rocker arm and the valve spring in a GM 2.2L motor


there is no specification for what you want
the valve clearance is between the end of the rocker arm and the end if the valve stem
the stem end is proud of the spring retainer so if your rocker arm is touching the spring retainer , you have a big problem as for the procedure it is set out in the workshop manual but if you don't have a manual it can be done like this
you will need the firing order of the engine first
now adjust no 1 piston valves when the next piston to fire has the valves in the rock position
that is the exhaust valve just closing as the inlet is just opening a bit of movement of the crank makes either valve move up or down
adjust no 1 piston valves
now move on to the next piston to fire and adjust the valves that were rocking
follow that procedure until all the valves are adjusted
for example
on a 4 cylinder engine with a firing order of 1--3--4--2
bring up no 1 piston and adjust the valves when the valves on no 3 piston are rocking
next piston to fire is no 4 so adjust no 2 piston valves
next piston to fire is no 2 so adjust the valves when no 1 valves are rocking
the procedure is the same for engines with any number of cylinders

Oct 19, 2016 | Cars & Trucks

1 Answer

When the valves are adjusted on the de-compression stroke can they be re-adjusted or is the head now faulty?


valves should always be adjusted with the cylinder being adjusted at top dead center(tdc). if you can rotate the motor by hand you can adjust the valves with no damage having being done.

Jul 29, 2014 | 1992 Toyota Pickup

1 Answer

I need the required valve & inyector clearance on a M11 engine


Cummins M11

Intake valve clearance 0.010 inch
Exhaust valve clearance 0.024 inch

The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

Feb 15, 2012 | Cars & Trucks

2 Answers

Valve lash procedure


i need to know how to adjust the valves on 02 pont sunfire

Nov 20, 2011 | 1991 Chevrolet K1500

1 Answer

Need to find out how to adjust vavles


If your engine is an overhead valve Briggs. You need to:
Remove valve cover
Locate rocker arms. Upper is exhaust, Lower is intake.
Loosen the lock screw in the center of the adjusting nut.
With engine at TDC and both valves closed adjust both valves by turning the adjusting nut to obtain proper clearance. Once set, tighten the center lock screw.
Valve adjustment specifications vary from model to model. Would need more engine information to get you that or it can be found online.
Reinstall valve cover, make sure gasket did not get damaged.
Adjust valves on a "cold" engine.

Feb 11, 2011 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

2 Answers

Overhead valves making noise like they need ajusting


Valve Lash ADJUSTMENT 1.6L Engines NOTE: Measure valve clearance with the engine cold.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the valve cover.
  3. Set the engine to Top Dead Center (TDC) of the compression stroke for the cylinder to be adjusted.
  4. Check the valve clearance. The valve clearance specifications are as follows:
    • Intake valves: 0.005-0.007 inches (0.13-0.17mm)
    • Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  5. After adjustment, tighten the locknuts to 11-14 ft. lbs. (15-19 Nm).
  6. Repeat for each valve to be adjusted.
1.8L, 2.0L and 2.5L Engines The 1.8L, 2.0L and 2.5L engines utilize automatic hydraulic lash adjusters to maintain proper valve lash at all times. Periodic valve lash inspection and adjustment is not necessary or possible. prev.gif next.gif

Sep 14, 2010 | 2000 Chevrolet Tracker

3 Answers

I have a 17hp briggs and stratton vertical intek engine that needs the valves adjusted again. What are the adjustments for the valves?


adjustment with 4000 feeler gauge
adjust top valve when the bottom valve is fully compressed and than with the top valve fully compressed adjust the bottom valve the same way.
very easy But remember to losen the center tork screw before adjusting the rocker arm nut

Apr 01, 2010 | Parks Optical Briggs And Stratton Engine...

2 Answers

New rebuild chatters


adjust your valves your oil pickup tube needs to be adjusted you need feeler guages to adjust the valves down properly
make sure lifters and oil pick up tubes are not clogged

feeler guage is---> thin pieces of metal cut to different sizes to hold under valve adjusters till the play and chatter gone
check by book what the feeler size needed for adjustment

Jun 07, 2008 | 1983 Chevrolet C3500

Not finding what you are looking for?
1982 Suzuki GS 650 GT Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...