Question about 2002 Honda CR 125 R

1 Answer

Stock needle position for cr 125 - 2002 Honda CR 125 R

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

Both the air and throttle screws set the same. Turn the screw in until it LIGHTLY seats then turn outward one and one half turns.

Could you take a moment and rate my answer? Thanks!

Posted on Sep 28, 2009

Testimonial: "thanks couldnt find the stock postion anywhere"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Grandson has 1992 cr 125 fuel overflowsthrough carb, had carb off and float appears ok


check and clean or replace the float needle assembly,set your float height ,check your throttle cable and make sure it has a little slack.

Mar 14, 2011 | 2002 Honda CR 125 R

2 Answers

Need to purchase battery. Don't know the size for a digitape 125


you may obtain the stock replacement for the tool, designated as a Duracell DL1/3N or as I did, utilize two more commonly available 1.5 V cellls Ag 13/357A but you need to then bend the positive battery contact terminal (the one more inside than outside) so that its point of contact is lowered somewhat..use your leatherman no problem.

Jul 12, 2010 | Starrett D125 Digitape 1Inch x 25...

1 Answer

How do you switch to reserve fuel tank on a Honda CRB 125?


Move the lever to RES position. If no RES, find the OFF and the ON, the RES is the other position.

Apr 12, 2010 | 2002 Honda CR 125 R

1 Answer

I need to know what kinda spark plug i need for my 2002 cr 125r


the parts shop should know what plug you need and any other plus that you could put in if the one you wont is not in stock but the plug number is on the plug in the bike

Jan 24, 2010 | 2002 Honda CR 125 R

1 Answer

What level on the needle valve does it go on for a stock cr 125


I believe it's in the middle, or out of five, third one down.
The needle is for you jetting after the pilot (idle) and before the main. Run it steady at 1/3 throttle for 10 minutes, shut it right off, and look at the spark plug color. It needs to be chocolate colored. Too light, move the needle up (Clip down) or too dark, move the needle down. (Clip up)
You can set the pilot and main jet the same way, by running it at an idle, then 1/2 to 3/4 throttle for the main jet.
Note, a bad lag or bog is usually too rich on pilot jet, or even into a rich needle. (too high needle)

Jan 14, 2010 | 2002 Honda CR 125 R

1 Answer

Cr 125, bike will not start after running out of fuel, have checked spark plugs and cleaned carbi needle and seet have used 40 to 1 2 strock petrol. bike still wont fire


DEPENDS IF YOU HAVE SPARK OR NOT,IF NO SPARK IT COULD BE YOUR STATOR/ IGNITION, HAS TO HAVE SPARK TO FIRE THIS IS WHERE I WOULD START FIRST

Jan 03, 2010 | 2002 Honda CR 125 R

1 Answer

My 03 cr 125 has low-endbog


Clean the carburetor. Move the clip on the jet needle downward one or two notches if your model has a stepped jet needle.
a20f5e4.gif

Nov 23, 2009 | 2003 Honda CR 125 R

1 Answer

How much 5w oil goes into each fork?


Using 5w oil with stock springs, your oil level should be about 100mm from the top with the fork fully compressed, damper rod pushed all the way down, and the spring out. I hope this helps and good luck. Please vote and leave a message.

Oct 30, 2009 | 2003 Honda CR 125 R

1 Answer

Honda cr 125 new top end rebuild started ok but when switched of petrol leaks out of overflow tube every couple of minuates


sounds like the float in the carb is stuck or set to the wrong hight give the carb a few taps with a screwdriver if that dont work take the carb off and check the float and needle.

Oct 08, 2009 | 2002 Honda CR 125 R

1 Answer

I have 1999 cr 125 what is the stock main get size


Standard main jet for a 1999 CR125RX is #162.

Aug 05, 2009 | 2002 Honda CR 125 R

Not finding what you are looking for?
2002 Honda CR 125 R Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...