Question about 2007 Suzuki Boulevard

1 Answer

I have a 2007 c90t. would like to know the cable length

I have a 2007 c90t. would like to know the clutch and rear brake cable length.want to replace with stainless steele

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 16 Answers

They are hydraulic. There is no cables. They are hoses.

Posted on Sep 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hi just bought a nissan1400 bakkie 2007 wana know why the clutch is very hard and how to repair


In most cases its the clutch cable. The Nissan 1400 clutch cable is secured to fire-wall with 2 nuts that act as adjusters as well. It is here where the problem lies. The cable easily damages at that point especially those after market cables. A new cable solves it.

Oct 01, 2017 | Cars & Trucks

1 Answer

2007 Suzuki Boulevard C90T will not start


Hi, Angel before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
C90 wont start
What Do Check When My Motorcycle Won Start Honda Shadow Forums Shadow... very comprehensive
Suzuki VL1500 Service Manual
OEM parts for Suzuki
Suzuki Intruder VL1500B Owner Manual

Jun 15, 2017 | 2007 Suzuki Boulevard C90T

1 Answer

Adjust handbrake in Hyundai tucson


The adjustment is made at the handle under the console:

ADJUSTMENT OF PARKING BRAKE STROKE

1.Pull the brake lever with a force of approx. 196 N (20 kg, 44 lbs.) and check the number of clicks.

Parking brake lever stroke (Standard value) : 8 clicks

2.If the number of notches is not the standard value, adjust the cable length with the adjusting nut on the equalizer.
3.The indicator light will go out when the brake lever is fully released, and will light up with the lever pulled one notch. If it does not operate properly, replace it.
4.After the adjustment, check that the rear brakes do not drag with the parking brake lever released.

Mar 05, 2015 | 2007 Hyundai Tucson Limited

1 Answer

How do i replace U-Joint on 2007 Suzuki Boulevard c90t


You have to pull the rear drive unit, rear wheel and then access the U joint by normally removing the rear swing arm. Make sure to apply Honda Molt 60 Paste grease to all splines (especially where the driveshaft enters the drive pod (take grease seal off, lube and put new seal on.) This grease is critical to prevent drive failure (seen it lots of times) Join volusiariders.com as theres a scad of info there and people who know these bikes inside out

Jul 14, 2014 | 2005 Suzuki Boulevard C90

1 Answer

WHAT IS DONE ON A 10K SERVICE FLHRC 2007


Change oil/filter
Service air filter (??? replace??)
Clean tappet oil screen (if applicable)
Change primary lube
Adjust Clutch
Change Transmission fluid
Check and adjust chain and belt
Inspect brake pads/discs
Lube; Front brake lever pin, throttle control cables, clutch control cable, jiffystand pin
Check operation of enrichener (carb model?)
Inspect fuel valve, lines, fittings for leaks
Check tire pressure
Check operation of all electrical equipment and switches
Check cruise control disengagement switch and clean connections
Check and adjust battery electrolyte level and clean connections
Change spark plugs
Check engine idle speed and adjust as needed (non-EFI?)
Lube foot shift, brake lever bearings, and speedometer cable (if applicable)
Check brake fluid level and condition
Inspect oil lines and brake system for leaks
Clean or replace fuel tank filter screen
Check air suspension, pressure, operation, leaks
Replace wheel bearings and replace lip seals where applicable
Check tightness of all fasteners except engine head bolts
Lubricate hinges, latches, fuel door, tour pak, and saddle bags
Adjust Springer rocker bearings
Check stabilizer links and engine mounts
Check wheel spoke tightness
Check rear brake pedaladjustment
check front fork bearings and adjust if needed
Check condition of rear shock
Check ignition timing and vacuum hoses
Test ride motorcycle

Jan 10, 2014 | Harley Davidson FLHRC Road King Classic...

1 Answer

2007 Equinox AWD doesn't work, message "Service AWD" on the dashboard is on. Diagnostics said the rear Clutch control module is not communicating, we replaced the module, still not communicating. Now we...


I'd go here http://www.haynes.com/products/productID/568 and buy the manual, and STOP throwing money at it until you actually know whats wrong..it can be very expensive that way.

Nov 01, 2013 | 2007 Chevrolet Equinox LS New Cars

1 Answer

I drive a toyota corolla 2007 face lift model. My car has 61k mileage on it. Oil levels are fine and i done a 60k service on my car. But my clutch is extremely hard. Its the hardest clutch i ever felt. i...


If it has a cable,it may need lubed if it is hydraulic type, it may have binding likage in the bell housing! I,d rather think it has a cable. DOES IT HAVE 2 FLUID CHECKS UNDER THE HOOD,ONE BIGGER ONE, AND ONE SMALLER OR JUST ONE BIG DOUBLE LOOKING CAP, OR LONGER LOOKING RESERVOIR ON A CYLINDER WITH FRONT AND REAR TUBES! THIS IS FOR THE BRAKES! If you see one more then it is for the clutch.

Sep 06, 2010 | 2007 Toyota Corolla

1 Answer

Clutch cable adjusters


Bowden cables like your clutch cable work on the law of the lever. Think of lifting up a heavy weight hanging on a rope using a lever balanced on a fulcrum. The rope is in tension and the fulcrum is in compression. To adjust the point of lift you could either vary the length of the rope or adjust the height of the fulcrum. The outer sleeve of your clutch cable is made out of plastic-coated steel, square-section wire and is resistant to compression forces along its length. This outer sleeve works as your fulcrum and, because it is flexible, lets you put it where it is needed - at the end of your handlebar. The cable inner is like the rope in the lever example and resists only stretching forces. It is threaded down through that snaking fulcrum back to where control movement is needed. The cable adjusters let you fine tune the length of the fulcrum, and therefore the lift range of the inner cable.,,,

Nov 10, 2008 | 2007 Boss Hoss BHC-3 ZZ4

1 Answer

Clutch cable adjusters


Bowden cables like your clutch cable work on the law of the lever. Think of lifting up a heavy weight hanging on a rope using a lever balanced on a fulcrum. The rope is in tension and the fulcrum is in compression. To adjust the point of lift you could either vary the length of the rope or adjust the height of the fulcrum. The outer sleeve of your clutch cable is made out of plastic-coated steel, square-section wire and is resistant to compression forces along its length. This outer sleeve works as your fulcrum and, because it is flexible, lets you put it where it is needed - at the end of your handlebar. The cable inner is like the rope in the lever example and resists only stretching forces. It is threaded down through that snaking fulcrum back to where control movement is needed. The cable adjusters let you fine tune the length of the fulcrum, and therefore the lift range of the inner cable.,,,

Nov 10, 2008 | 2007 Benelli Tre-K 1130 Amazonas

Not finding what you are looking for?
2007 Suzuki Boulevard Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...