Question about 2003 Harley Davidson FLSTCI Heritage Classic

1 Answer

How ot install easy pull clutch flstic 04 - 2003 Harley Davidson FLSTCI Heritage Classic

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

It depends on the type of unit you have. If you know who made it, you can usually download installation directions from their website.

Posted on Sep 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to replace 04 Vue clutch master cylinder

go to this link and scroll down the page and near the bottom you should see where its saying (How to replace 04 Vue clutch master cylinder) hope this helps you out if not just look on the page you might find something to help you out... How to replace 04 Vue clutch master cylinder Google Search

Oct 27, 2017 | Cars & Trucks

1 Answer

My 04 drz125l bike wont disengage when clutch is pulled why? how do i fix?

adjust your clutch sounds like its slipped. an easy job. follow cable to both ends and see if there is any loose play as you engage. adjustable spanner and screw driver. Red

May 22, 2014 | Yamaha Royal Star Tour Deluxe Motorcycles

1 Answer

How to jump out clutch interlock

pull connector from switch and use a paper clip or other piece of wire to connect the 2 terminals in the connector. Be careful not ot start the car in gear with the clutch out! Any more questions, let us know.

Sep 15, 2010 | 1995 Ford Ranger Supercab

1 Answer

What is the torque for the bolts that hold the clutch spring plate reduced effort clutch spring on a 2003 FLSTIC

I've never really torqued these bolts and I've replaced plenty of the diaphragm springs. Usually I put stronger springs in the clutch since I'm building up the horsepower of the engines. I put a drop of Loctite 242 (med, strength blue) and tighten the bolts to about 25-30 foot pounds. Check the standard torque for a grade five bolt of the size that are in the clutch.

Oct 27, 2009 | 2003 Harley Davidson FLSTCI Heritage ...

1 Answer

'04 Triumph Tiger clutch cable

If it is running alone the back bone then yes you will have to remove the tank.

Oct 16, 2009 | 2004 Triumph Tiger

2 Answers

1998 ford expedition how to install rear spider gears

Find a PICK-your-PART auto salvage and go get a whole rearend for $150 or so. You will be way far ahead. Or submit to the BLUE OVAL (dealership). Sorry no easy fix.

Sep 03, 2009 | 2000 Ford Expedition

1 Answer

How to change the back wheel bearings on my 04 toyota 4runner

Pulling the axle is relatively easy. The problem you are going to have is replacing the bad bearings. They are pressed onto the axle shaft, and, if you do not have a large press and the necessary special tools to use the press properly, you are simply not going to be able to do this job yourself. I know that this is not what you want to hear, but, I do this job quite often, and I know very well the level of difficulty. I can give you the directions, but the pressing is the main issue that will hinder you. You are also going to need to replace the brake shoes after the axle is repaired.

Mar 12, 2009 | 2004 Toyota 4Runner

1 Answer

Why it is difficult to engage the gear when the gear box is warm up.

This may be wear clutch related, if the clutch is starting to wear out past a certain point of clutch disk thickness the trans gears don't stop when you press the clutch in, this causes hard to shift issues like yours, one question does the clutch feel soft ot have to much play?

Oct 08, 2008 | 1996 Mitsubishi Galant

1 Answer

Clutch 1995 Saturn SL15 speed, 150,000 miles

The service manual calls for removing the motor and trans as one unit before seperating. To get ust the trans out you have to pull axle shafts and take front end parts off. It's not an easy job and does require a few special tools to do it. If your not used to doing fairly heavy repairs at home you should have someone else do it or plan to really take your time and have to buy a few extra things along the way.

May 14, 2008 | 1993 Saturn SL1

Not finding what you are looking for?
2003 Harley Davidson FLSTCI Heritage  Classic Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76691 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides