Question about 2003 Victory V 92 C

1 Answer

Broke spring on kickstandcheck engine flashing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 376 Answers

Get a new spring back on. When you hit a bump it is activating the switch.

Posted on Sep 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

This is a 4cyl diesel Beetle. The timing belt broke while driving. Dealer claims no damage done, replaced belt and car was driven for a few weeks. Began to start a bit sluggish, dealer said glowplugs...


my books show it as a interference engine in which case valve damage is most likely to occur
however if that was the case , it would be having a miss from the start and would not run 2 weeks before something happened
if a valve spring breaks there could be valve piston contact but it is doubtful if that would destroy the engine but again breaking valve springs is rather rare on diesel engines
the engine would not just quit but would rattle and bang it's head off then develope a big noisy miss from a hole in the piston
so I suspect a timing belt problem from when they removed/replaced the head after the glo-plug fix or a crank/cam shaft position sensor or wires ( possible faulty connections for the cam shaft)
I would suggest finding an accredited service center for a proper diagnosis and quote for engine repairs

Apr 12, 2017 | 2003 Volkswagen Beetle TDI

1 Answer

Have an Excell 2500, VR2522...... Pull cord broke and now i think the spring is broke; where can I get a new spring and directions to reassemble the pull start?


That pressure washer uses a Honda 5.5 hp overhead cam engine
You need to get the model number of the Honda Engine and then Click Here to go to the ereplacementparts.com website and put the engine model number to order the parts.

Jun 23, 2011 | Garden

2 Answers

I have 2000 ls , took eng apart and found cam chain broke. and wonder what cause it to break clean? nothing is bang up.should i place cam chain and that be it or there more to it?


Very rare that a chain breaks. I'd replace the chain and before closing it up, turn the engine by hand and see if anything is binding or frozen in the valvetrain. Also look carefully at the valve springs to make sure that no valves have bent. (if bent, most times the spring will not return to normal height)

May 16, 2011 | 2000 Lincoln LS

1 Answer

Turn signal switch won't lock into left turn postion. Signals flash if I hold the switch to the left. Right turn locks and unlocks properly. I have not yet disassembled to switch to see if a bearing or...


That is the first thing that I would do. If something came loose just replace it unless something broke then you have to replace the whole switch. If it was just a spring or bearing you should be able to put it back in unless something broke like I stated earlier.

Feb 28, 2011 | 1998 kawasaki VN 800 Vulcan Classic

1 Answer

Loud noise from dishwasher door. then no resistance. what could this be and can it be repaired


It sounds like you may have a broken door spring. You will have to take off the bottom panel and with a flash light you can look to see if one of the springs came off or broke. If the spring is broken you will have to purchase a new spring and replace it.

Feb 25, 2011 | Hotpoint 23 in. BF41 Built-in Dishwasher

1 Answer

I have a craftsman 550 manual push mower the idle spring on the accelerator broke when I a branch broke the spring which is now gone how do I fix it


This sounds like the governor spring that is very important in controlling the speed of your engine when under load or no load conditions, the speed should always be the same. You will need to get one that is made for that engine an exact replacement. That is about all I can suggest that you do. I hope that helps you out. Best regards and good luck,

Dec 24, 2010 | Craftsman Garden

2 Answers

CAN THE SPRING BE REWOUND ON MY MANTIS TILLER THE CORD BROKE, AND WHEN I WENT TO RE INSTALL THE SPRING CAME OUT


Go to your local small engine supply store with the model an serial numbers. you can buy the spring all ready wound and in a metal container that will drop right in and you will be set togo.

May 01, 2010 | Mantis 2-Cycle Tiller

1 Answer

Check print cartridge flashing


cartridge circuitry damaged, replace with new one

May 26, 2009 | HP PSC 1401 All-In-One Printer

1 Answer

Air bag light flashing


the clock spring behind the steering wheel could be bad,about a $100.00 part through Ford

Apr 18, 2009 | 1994 Ford Taurus

Not finding what you are looking for?
2003 Victory V 92 C Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...