Question about 1981 kawasaki Csr 1000

1 Answer

How much is a set of exaust pipes - 1981 kawasaki Csr 1000

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

$400-$700. You may want a carb adjustment from dealership to optimize power with your new set of tooters.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my 2005 scion xb has a smelly exaust fumes, no exaust fumes color. it pass the smog.


This sounds too me like the catylitic converter is getting bad, tapon it and see if it rattles. This is usually what causes a sulfer like odor coming from the exhasr.

May 25, 2014 | GE Pipe exaust & rivet - WE14M101

1 Answer

Oil smell and smoke 2006 buick lucerne


is the smoke coming from under the car or out the exaust pipe?
under the car ! you have an oil leak and its probably landing on your exhaust pipe which by the way can ignite and go on fire if the pipe gets too hot. if its out the exaust ! computer or air intact problems. worst case: rings are bad and oil is mixing with the gas in the piston chamber. Hope this helps a little good luck and God Bless

Feb 03, 2014 | 2003 Chrysler PT Cruiser

1 Answer

Hi, I have a 1980 Honda XR250. The compression is around 120 (with decompression disconnected). It blows smoke and will not rev high - I assumed carb dirty, cleaned it but still reluctant to go to high...


Might be a good idea to check your timing first and then if the timing is ok try removing your exaust pipe and running it for a few minutes without the exaust system installed. I have encountered a couple of bikes where the exaust system has carboned up and will not allow the engine to breathe especially at hiogher rpms. A day in the gunk tank for the exaust pipe did the trick and the bike ran like new. (Gunk will remove all the paint too)

Jan 22, 2013 | 1987 Honda XR 250 R

1 Answer

95 Gran am engine lith blinks and exaust pipe gets red hot runs rough


Should be your catalytic converter is plugged up.
should be replaced

Jun 25, 2012 | Cars & Trucks

1 Answer

The peice that coms off engine to exaust y pipe? but has 4 pipes an goes to one. the exaust whats it called?? it has a crack an a hole in it an exaust is loud!.?????


Pollution control,air injection,you could just pinch the small pipes closed with a pair of vice grips and never know the difference.

Nov 21, 2010 | 1999 Plymouth Voyager

1 Answer

To much noise


They do have a lot of vibration. Check all bolts to be sure they are tight. Set it on something that will help quiet the vibration (rubber mat or the like). If it is exaust noise, how old is the unit and could it need a new muffler? I piped the exaust on mine into a larger muffler mounted on the frame with rubber grommets.

Sep 25, 2010 | Coleman Powermate Portable Generator...

1 Answer

My 2001 chevy s-10 won't start, the exaust pipe


make sure all the dirt is out of the exhaust pipe. sounds like it is clogged.

Jan 03, 2010 | 2001 Chevrolet S-10

1 Answer

Dryer will not dry on auto setting, drys slow , over an hour on high setting


This sounds like your venting is eather too long or has a kink in it or is full of lent. First check behind the dryer for a crushed hose. Then check where the vent exausts. (The vent cap can also freeze up in the winter) If you are using plastic pipe (not recomended) change it too a rigit metal pipe. You should only have two elbos in your run. The shouter the pipe the better your auto dry will work.

Dec 22, 2009 | Dryers

1 Answer

Why woulod oil come out of my exaust pipe? 1996 ford taurus


Either your valve seals are bad or you piston rings are wore out. I would say it is the valve seals though.

Mar 23, 2009 | 1996 Ford Taurus

1 Answer

Exhaust tip for tuck


If you are going to rivet or bolt in on you need to drill holes through both tip and exhaust pipe.

I like having them welded on to prevent problems in the future. Any exhaust shop can do that for you.

Aug 29, 2008 | 2004 GMC Sierra

Not finding what you are looking for?
1981 kawasaki Csr 1000 Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...