Question about 1982 kawasaki KZ 1300 A4

1 Answer

1980 kz1000 wont go in gear

I just got my old kz1000 running half way need a little more time to get it perfect, minor problems. but my clutch was moving i could see it through the oil hole but now nothing after i get it running, i drained all the oil out and left it setting with no fluids for a few days, i hope the oil not being in there hurt my clutches or something does any body have a clue i only have few dollars that i can door my bike so i need a fix

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • kawasaki Master
  • 8,404 Answers

Shouldnt be a probelm.

a

Posted on Sep 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

29 mm smoothbore carbs on 1980 kz 1000 motor idles down real slow then shuts off


Hi, Virgil and the usual suspects are:
1. Idle speed improperly adjusted.
2. Air fuel mixture screws not properly adjusted.
3. Inlet system air leak.
4. Leaking accelerator pump.
5. Loose low-speed jet.
6. Plugged low-speed jet.
7. Contaminated or plugged low-speed circuit.
8. Enrichner valve/choke not seated or leaking.
9. Multi carburetors out of sync and need to be balanced.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
TOPIC Rev slow to drop off after releasing throttle
KZ1000 slow to settle into idle
Kawasaki KZ1100 Service Manual
OEM Parts for Kawasaki
1980 kawasaki kz1000 ltd oem factory used owners manual KZ1000 LTD kz1000...

Jan 01, 2017 | kawasaki Motorcycles

1 Answer

Manual clutch will go into gear but wont move in any of the 5 gears


You may have an internal transmission problem or clutch issue. If you can shift the car into gear while running without using the clutch pedal, suspect a defective clutch

Feb 28, 2016 | 1990 Honda Accord

1 Answer

Subaru justy wont go into any gear


when was the clutch plate last replaced was it lately and the problem just started after the change
next there is a bush/bearing in the center of the crankshaft that failes/ dry and that seizes in the input shaft of the gear box and makes the clutch useless as it drives the box all the time
another thing is any oil or grease on the clutch lining will stick the plate to the flywheel face and cause a problem
if the clutch plates are old , the damper springs can come out /break and intere with the flywheel mounting bolts
removing the transmissions and checking the clutch assemblies will reveal the reason for the failure

May 21, 2017 | 1990 Subaru Justy

1 Answer

1980 TS250 runs backwards


It was a normal effect on those old engines.Try to roll it downhill with 2nd or 3rd gear in and pop the clutch to start it.However you must adjust the plate that carries the ignition coil (it is located behind the stator's rotor/magneto wheel) to the correct advance angle if this problem insists.It is part number 2 in the picture.http://partstream.arinet.com/Image?arik=s4v92978S7HV4vH84i3c&arib=SUZ&arim=IbMgUI0ORSbT264E03VzmA2&aria=qFhQrjJlZwkA1lGsp3MiEw2&ariz=3&ariv=http%3A%2F%2Fwww.babbittsonline.com%2Fsuzuki-motorcycle-parts

Feb 06, 2012 | Motorcycles

1 Answer

Hi,. there is a problem with my clutch. it was working fine when i drove around but now when i tried to push the clutch down to take it into first gear it wont go all the way down therefore not letting me...


can you select gears with motor not running? ie dont need to use clutch to do this.
Is foot leaver jamming inside the car?
is clutch arm (or slave cyl) at bell housing jamming.
If above ok then looks like motor and clutch out time.

Aug 11, 2011 | 2000 Daewoo Nubira

1 Answer

I have a 2001 raptor 660 that wont start off the electric start no matter wat i do. I have the repair manual an iv'e checked the spark cleaned the carbs air filter put a new choke cable in it nothing...


a common problem with those, amongst many other yamahas, is the starter clutch gear. if it's not the starter solenoid , most likely it's the starter clutch gear.

Jan 12, 2010 | 2002 Yamaha WR 426 F

1 Answer

I replaced the handlebars on my 81 yamaha 650 maxim. after that, the throttle won't completely engage the gears. it goes forward with a little gas, but if you open it up, the engine just revs and will not...


Chances are the new bars are a bit taller than the old bars. It sounds like the taller bars are making you stretch the clutch cable. No freeplay at all in the clutch lever, Right? If the clutch cable was not re-routed causing the stretch, the only thing you can do there is get shorter bars or get a longer cable from a similar bike or have a custom cable made at the shop. The blinkers is just an error in how the wiring was reconnected.

Can I get a “very helpful” rating on this answer?

Sep 01, 2009 | 1980 Yamaha XS 650 G

2 Answers

Toyota supra turbo 1990, manual (7mgte engine) Clutch problem


you need to bleed the clutch system.. have someone pump the clutch pedal three or four times, hold it down and release the bleeder valve( make sure the person holds the pedal down till after you tighten the bleeder valve back down) repeat this four or five times or till the clutch pedal feels like it did before.. good luck keith...

Mar 21, 2009 | 1990 Toyota Supra

1 Answer

I have a 2001 Chevy Tracker/Suzuki tracker--Sometimes when I try to change gears it will not go into gear--It is just like I have not engaged the clutch --But I am? Is it the clutch or throw out...


it could be the clutch if ur clutch is not disengageing properly it wont let u and how old is the gear box u may find it is that if its old or u may also need to check the gearbox oil if that has not been changed in years since u brought the tractor it may have grit and dirt stoppin the gears movin perfectly, personaly i think ur gear box is nakered

Oct 02, 2008 | Chevrolet Tracker Cars & Trucks

Not finding what you are looking for?
1982 kawasaki KZ 1300 A4 Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...