Question about 2008 kawasaki Versys

2 Answers

Dim rear right turn sinal LED on "2008 Kawasaki Vulcan 900 custom

I have a "2008 Vulcan 900 Custom" (this website didn't have my bike as a choice) with led lights all around. The right rear turn signal led's are flashing very dim. Connections are good as well as fuses. What should I look at next?

Posted by on

  • Anonymous Mar 22, 2014

    tried to jump start the battery. no power whatsoever

  • Anonymous Mar 30, 2014

    It skips in gear. Stays in seconds but skips

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 355 Answers

Well i would check ground wires and clean ground wire to light and i would see if you have 12 volt at hot lead or 5 volt some led do not run 12 volt at them but i would make sure ground wire is good and clean if the led light is replaceable i would pull it out and clean socket or try swapping with other side to see if build is the issue hope this helps

Posted on Sep 24, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • kawasaki Master
  • 3,433 Answers

Chk for ground feedback

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I connect the alternator to my rectifier for my Kawasaki VN 900


Hi, Fransina for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Vulcan 900 Stator Information Thread
Kawasaki Vulcan VN750 stator replacement without removing the engine
Kawasaki VN900 Custom Service Manual
OEM Parts for Kawasaki
Kawasaki vn900c Quick Reference Manual

May 08, 2017 | 2010 kawasaki VN900 Custom

1 Answer

I have a vulcan 900 custom do i have to splice the wiring to install the rear turn signals or its plug and play


Hi, Phillip if they are OEM should be plug N play otherwise get out your splicing kit and if you are going with LED lights you are going to need a load equalizer sorry you can't find the first and best tool you ever bought for your Kawasaki despair not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
rear turn signal removal
Arlen Ness Badlands Turn Signal Load Equalizer Harley Davidson Models 91...
KAWASAKI VN900 CLASSIC Service Manual
OEM Parts for Kawasaki
http://www.kawasaki-techinfo.net/searchOM_nv.php?view_lang=EN&spec=OC&book_no=&lang_code=

Apr 11, 2016 | Motorcycles

1 Answer

Runs for 30 minutes, then why does engine stop?


Hi, Freerick the following applies to carbureted also fuel injected models and the usual suspects are:
1. Severely discharged or damaged battery, 9 volts or lower.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Water or dirt in the fuel system, carburetor or filter.
11. Restricted, blocked or kinked fuel line.
12. Fuel tank empty.
13. Gas cap is not venting properly or fuel tank venting system blocked.
14. A failed fuel pump, pressure regulator and or fuel injectors.
15. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
16. Needle and seat stuck closed in the float bowl.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
http://www.kawasakimotorcycle.org/forum/kawasaki-cruisers/146296-2008-vulcan-900-custom-hesitates-hard-acceleration-after-about-20-30-min-riding.html
2008 Vulcan 900 CUts out and shuts off HElp Kawasaki Vulcan Forum Vulcan...
https://www.vulcanrider.se/en/kawasaki-vulcan-service-manuals http://www.kawasaki-techinfo.net/index.php?view_lang=EN&spec=OC

Jan 03, 2016 | 2008 kawasaki Vulcan 900 Custom

1 Answer

How to remove rear pulley on vulcan 900 custom


Hi Anonymous, I am sorry you can't find the first and best tool you ever bought for your Kawasaki but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
https://www.tradebit.com/filesharing.php/search/0/2012+kawasaki+vulcan+900+custom

Aug 16, 2015 | 2012 kawasaki Vulcan 900 Custom

1 Answer

Not charging battery


Sounds like its your charging system, either the alternator or regulator/rectifier.

Dec 28, 2013 | 2008 kawasaki Vulcan 900 Custom

1 Answer

Fuel is leaking into my oil pan


Perform a compression test. Your looking for a bad ring.

Sep 23, 2013 | Front Splined Floorboard/Footpeg Adapters...

1 Answer

Cant locate oil sight glass for 2008 Kawasaki Vulcan 900 classic,where is it located


Not sure of the 900 Classic, but look to the rear of where the gear change pedal is attached to the splined shaft coming from the gearbox. Is the window there?

Feb 03, 2013 | 2008 kawasaki Vulcan 900 Classic

2 Answers

IS MY 2008 KAWASAKI 900 A CUSTOM OR A CLASSIC I UNDER STAND I NEED THAT INFO SO I CAN ORDER A WINDSHEILD . MY VN # IS JKAVN2B108A033752 THANKS FOR INFO


The VIN decoder info is below. Since the Vin shows it to be a VN900B, the bike is the "Classic" model. Please rate my answer. Thanks. tombones49_142.gif

May 23, 2011 | 2008 kawasaki Vulcan 900 Classic

1 Answer

My vulcan tail light stays on after with the ignition switched off. What can I do to stop this reoccuring


The ignition switch has three positions. Off at 6 o'clock, on at about 7 o'clock and park at 9 o'clock which will leave the tail light on and also shut the bike off. Just have to make sure when you turn the ignition off that the key is straight up and down.

May 22, 2011 | 2008 kawasaki Vulcan 900 Custom

1 Answer

Kawasaki Vulcan 900 Custom - sat the winter,


Did you connect the poles correctly and are the bolts tight to keep good contacts?
Try usin a trickle charger to jump the battery.

Mar 21, 2010 | 2005 kawasaki EN 500 Vulcan

Not finding what you are looking for?
2008 kawasaki Versys Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...