Question about 2003 Harley Davidson FXDL Dyna Low Rider

1 Answer

My throttle on 03 Dyna Lowrider became Very tight all of the sudden and does not snap back when released. Any ideas/suggestions? It does throttle up and down if I force it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,167 Answers

Seized cable try and squirt some wd40 down the cable and move it up and down and get back to me

Posted on Sep 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust the idle on my 03 dyna wide glide


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Aug 18, 2012 | 2003 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

My throttle grip will not return to idle position by it self


1. Check to see that your throttle stop isn't locked.
2. Lube the cables.
3. Lube the throttle sleeve.
Hopefully, one of these will solve the problem. If not, post again and I will try to give you more solutions.

Jun 02, 2012 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

"1997 dyna lowrider 80cubic inch


Check for air leaks around intake w/ wd-40 spray if leak rpms increase..or also check accelerator pump is shooting work throttle should see a stream of gas in venturi..

Sep 18, 2011 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

Where is the drain plug on a 2004 dyna lowrider?


The oil tank is on the bottom of the transmission. Two drain plugs. The center one is the transmission drain, the one towards the front on the left side is engine oil drain.

May 22, 2010 | 2004 Harley Davidson FXDL - FXDLI Dyna Low...

1 Answer

2008 dyna lowrider run switch will not activate,


"The two small hydo lines entering it seem to be loose and spring loaded turn screw is also loose"

I think you're referring to the two throttle cables and the throttle lock screw on the bottom of the throttle mechanism.

The "run/stop" switch is located inside the switch housing on the throttle side. It has three wires running to it. If the switch does not work, it may be defective.

To replace the switch, you must remove the two bolt that hold the switch halves together. Carefully seperate the two halves. the "Run/Stop" switch is in the front half of the switch housing. The switch is held in by a couple of small screws. Remove the switch and unsolder the wires taking note of which wire goes where. Resolder the wires to a new switch and install the switch in the housing. Reassemble housing keeping it positioned up firmly against the front brake master cylinder. Check the throttle for proper operation prior to starting the engine.

Apr 09, 2010 | 2003 Harley Davidson FXDL Dyna Low Rider

Not finding what you are looking for?
2003 Harley Davidson FXDL Dyna Low Rider Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...