Question about 1986 Suzuki LS 650 Savage

1 Answer

KAMSHAFT AND ROCKER ARMS - 1986 Suzuki LS 650 Savage

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Bin them

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rebuilt engine 3800 and getting a tapping/ticking sound at cold start. Brand new lifters rocker arms are not new.


Here are 3 causes for lifter tick!
Bad Lifter, Dirty Oil Deposits, Bent Push Rod, The rocker arms will make a noise if push rod clearance is not adjusted right. God-Bless! and hope this helps you!or the rocker arms may be worn.

May 20, 2016 | Cars & Trucks

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

How to set rocker arms on 2.2 4clyder s10 pickup


Rocker arms on a 2.2l gm engine are non-adjustable, they should have a shoulder stud not threaded all the way down just torq them.

Nov 04, 2014 | Cars & Trucks

1 Answer

If i put the rocker arms in wrong on my 01 buick


two things one you will either get no compression in the motor or you will get excessive knocking from the lifters adjusting the rocker arms properly will stop this . follow this link this will show you how to adjust rocker arms.

Sep 28, 2014 | Cars & Trucks

3 Answers

Why does my 8hp Honda keep braking rocker arms


stuck valves are the main cause of breakig rocker arms

Sep 22, 2014 | Honda 8 HP Engine

1 Answer

Installed new oil pump and now have broken rocker arms


THe rocker arms are broken because there was not enough downward movement in the valves to allow the cam to complete its turn. IT happens when the valve spring retainer either hits the top of the valve guide or the valve springs are fully compressed forming a solid block . If you have hydraulic valve adjusters I would be suspicious of a lack of movement (seized) in the ones that broke the rocker arms

Feb 20, 2013 | Ford F-150 Cars & Trucks

1 Answer

P 2647"A" Rocker Arm Actuator


Your going to need a air pressure regulator or better yet if the ECM found fault price it and replace it
  1. Start the engine, and let it run for 5 minutes, then turn the ignition switch to LOCK (0).
  2. Remove the cylinder head cover.
  3. Set the No. 1 piston at top dead center (TDC).
  4. Move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A should move independently of the secondary rocker arm B.
    1. If the intake secondary rocker arm A moves freely, go to step 5.
    2. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, then check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
    3. Repeat step 4 on the remaining intake secondary rocker arms with each piston at TDC. When all the secondary rocker arms pass the test, go to step 6.
    4. Check that the air pressure on the shop air compressor gauge indicates over 400 kPa (4.0 kgf/cm2, 57 psi).
    5. Inspect the valve clearance.
    6. Install a 10 x 1.0 mm adapter to the inspection hole, then connect the air pressure regulator
  5. With the specified air pressure applied, move the intake secondary rocker arm A for the No. 1 cylinder. The secondary rocker arm A and secondary rocker arm B should move together. If the intake secondary rocker arm A does not move, remove the secondary rocker arms as an assembly, and check that the pistons in the secondary rocker arms move smoothly. If any rocker arm needs replacing, replace the secondary rocker arms as an assembly, then retest.
  6. cansmo_32.gif
cansmo_33.gif

Aug 23, 2011 | Honda Accord Cars & Trucks

1 Answer

Loud rattle noise in Camshaft


First, your engine has rocker arms, if you have a 4 cylinder you have 8 rocker arms, and if it is a 6 cylinder you have 12 rocker arms. Now if it is indeed a rocker arm making the noise, the cause is most likely a bad lifter or a worn cam shaft.

Apr 02, 2010 | 2001 Chevrolet Cavalier

1 Answer

Mixed up my rocker arms when replacing my head geasket


the arms for INTAKE should all match, and the arms for EXHAUST should all match. I dont think you can put them on wrong, if you are hitting a piston you need to verfiy the cam timing, I think that is where your problem is.

Sep 27, 2009 | 1990 Acura Integra Hatchback

1 Answer

Fiero f2 motorcycle engine makes tappet sound when warm.sound disappears as temperature rises.engine is butter smooth with good milage. timing chain&adjuster have been replaced.Are the rocker arms a...


Rocker arms are responsible to move the valves and hence control the valve timing. So if youe mileage and power goes okay,i don think there is some problem with the rocker arms. 

Mar 22, 2009 | 2005 TVS Fiero FX

Not finding what you are looking for?
1986 Suzuki LS 650 Savage Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5057 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...