Question about 1994 Suzuki VS 800 Intruder

1 Answer

I have a loss of power. When the RPM's go I don't

I have a loss of power. When the RPM's go up I don't change the throttle position and they come back down almost to the point of stalling.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Bin it

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have clean the throttle body on a 2008 nissan qashqai and the rpm are going from 1500 to 2000 and coming back without touching any pedal.we took the throttle switch and the rpm went back to normal.


need to perform closed throttle position relearn and IAVL relearn. unfortunately IAVL gets done with nissans consult scanner, so you have to get a scanner that will do it, or go to a dealerand get it done, but closed throttle position relearn you can do at home by turning the ignition key on for 10 seconds and turning it off for 2 seconds 4 times in a row. you need to perform both operations fot the car to run right / back to normal. when you cleaned the throttle chamber, you changed the closed throttle position because the chamber is clean now and the throttle plate has moved some.

Aug 10, 2016 | Nissan Cars & Trucks

2 Answers

What can I do to fix my 1988 Ford Bronco xlt with a 351 engine that has rough idle and loss of power when in drive?


Fuel filter. Low fuel no power. Catalytic converter. no air out, no air in. loss of power.

Jan 25, 2015 | 1988 Ford Bronco

1 Answer

2003 Mitsubishi lancer 2.0 ralliart. Complete loss of power under wide open throttle between 2,000 - 3,000 rpm. Car idles fine and continues accelerating after 3,000 rpm under wide open throttle just fine....


oxygen sensors buddy, and there is two of them. one above the engine and under. you have to cut it enough to where you can splice and re wire another sensor on.

Feb 23, 2013 | Cars & Trucks

1 Answer

Kawasaki jet ski stx power loss at high throttle


You might want to post this question in a different section. This is the computer games section.

Aug 16, 2012 | Video Game Consoles & Games

1 Answer

P0068 on a 2006 Dodge Ram 1500 SLT. Rough "hunting" for idle. Momentary lag/loss of power from a stop. Random RPM changes while at a constant speed. Sometimes it feels like it drops out of gear...


P0068 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of power
- Engine rough idle Possible causes - Large vacuum leak
- Leaking air duct system
- Mass Air Flow (MAF) poor electrcial connection
- Manifold Absolute Pressure (MAP) poor electrcial connection
- Faulty Mass Air Flow (MAF) sensor
- Faulty Manifold Absolute Pressure (MAP) sensor
- TP sensor not seated properly.
- Faulty Throttle Position (TP) sensor.
- Dirty throttle body
When is the code detected? The Powertrain Control Module (PCM) monitors operation rationality check by comparing sensed throttle position to mass air flow readings
P0068 DODGE Description The Powertrain Control Module (PCM) monitors a vehicle operation rationality check by comparing Throttle Position (TP) to Mass Air Flow (MAF) readings. If, during a self-test, the comparison of the TP sensor and MAF sensor readings are not consistent with the calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.

Jul 10, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

P1613 fault code & engine will not rev over 3000 rpm when you get to 3000rpm it then fluctutated between 2500 rpm & 3000 rpm causing the car to buckaroo


Crank sensor or engine speed sensor is faulty.

Fault:
Irregular power loss on accelerating
The speed of the engine is limited till 2500rpm
Frequent loss of crankshaft position sensor signal

Cause:
It is caused due to leaking from thermostat housing into crankshaft position sensor harness multi-plug

Remedy:
Check and clean the crankshaft position sensor harness multi-plug contacts. Rectify the engine coolant leak from the thermostat housing if found. Take a note of the engine coolant level and monitor it for changes, showing a leak is indeed occurring.

Oct 24, 2009 | 2005 Peugeot 405

1 Answer

Loss of power on 90 loyale,


Are you getting a service engine light?If not could be a air.or fuel delivery issue,i.e...fuel filter,fuel pump,or even air filter.If so,could be the throttle position switch,or the mass airflow sensor.

Apr 13, 2009 | Subaru Loyale Cars & Trucks

1 Answer

Lossof power and ets off inicator on


check fuel pressure 1 fuel pump 2 fuel pressure regulator and 3 fuel filter.

Oct 30, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1994 Suzuki VS 800 Intruder Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

82322 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5223 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...