Question about kawasaki ZX-6R Ninja Motorcycles

1 Answer

I have an 06 636 with 19,000 miles on it and was washing it which i try to make sure i dont get any water in the breather box but as you know even riding in the rain it is sometimes hard to do. since i have washed it, it runs really rough and aftersitting for a couple of weeks it did not want to start. i had to give it half throttle for a while before it would start

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 9 Answers

Change the plugs u have moisture on the plugs when u take them out i`m sure they`ll be a little rusty

Posted on Sep 10, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Model MDB5601AWW leaking around the side plastic box on left wall inlet that has water hose. What needs done?

-Here sample solution.
-The plastic box or cap you're talking about is the " Breather Cap"
-Check the drain tube from the breather cap to the sink. It must be clean and no block.
-Make sure the breather cap stays in up right. (Straight Up)
-Check the breather cap's Cap . Any big chuck of food waste stuck inside or not. If so the clean it.
-Check the whole breather cap. Any crack...? If so the replace new one.

Good luck ,enjoy and wash every day


Oct 25, 2017 | Maytag MDB5601AWW Energy Star Built-in...

1 Answer

I took my vibe to the car wash about 40 feet out of the parking lot in started running on 3 cyl. and a light smoke coming from the exhaust i pulled off the road gave it a few good revs and she started...

The car wash pressure may have disconnected an electrical connector part way or completely. Check for this all around the engine and transmission. Touch and wiggle all of them! Dont forget to check under the car all the back to and around the gas tank. Also check for a vacuum line that is popped off or even broken.
Aside from that, water has got into something. Check all power distribution boxes for moisture.
If you dont know how old the plug wires are, or they are the originals, you should replace them.
With plug wires, its the age, not the miles.

Jul 31, 2011 | 2005 Pontiac Vibe

1 Answer

My washing machine wont rince clothes it just humms.

Your machine might have a blocked water level sensor or sensor tube.
Many machines have independant sensors for when the water level is full and when empty.
After the wash cycle, if the machine just continues to try to pump water out (even when empty), then it's most likely a sensor problem.
Sometimes, the sensor also has a breather tube, and if this clogs with fluff / debris, similar symptoms esult.

Apr 09, 2011 | Frigidaire Hardware & Accessories

1 Answer

I have a 2005/6 Honda Shadow Aero 750, I was coming home today which intails drropping dow a mountain....about 2000 feet over 5 or 6 miles....when i got to the bottom and noticed it was blowing...

Check your oil level. Engine braking down a mountain side could be overloading the breather system, only because most people do not know there are pollution tubes under and behind the motor, in front of the rear wheel. They collect oil and crud from the engine blow by and recycle it through the carburetor intake. If they are full it collects in the bottom of the air box. This is probably causing the smoke and oil you describe. Place a pan under the tubes and pull the plugs out. All the oily crud should come out. Then put the plugs back in. Also check your air cleaner for oil saturation you may have to wipe out the bottom of the air box or even replace an air filter. Also check that a breather tube has not come off of the top of the motor. This could also cause the oil between the cylinders you describe.

Aug 20, 2010 | 2005 Honda VT 750 Shadow Aero

1 Answer

Oil on breather tubes.

Not sure how many miles you have but oil on breather tubes (depending on how much) is normal the problem is when you have excessive blowby and high oil consumption. When was the top end done last... If never, it's due....

Sep 08, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Need HELP! locating the MAP sensor and the Camshaft sensor for an

The MAP sensor is on the breather hose next to the breather box,The speed sensors are pictured below.Please take time to rate this a fixya.

May 16, 2009 | 1996 Plymouth Grand Voyager

1 Answer

GE DishWasher starts/drains, but no water pumped for cleaning

-You mean not completely pump out. After it's done Some water still inside right...?
-Mostly the breather cap is clogged or is locate little too low. Check it out and clean see what happen, and make sure it stay up right. not horizontal.
-Where is the breather cap..? Most installer install under the counter be hide the sink. 1 drain tube from the washer to it. And one from the breather to the sink or disposal. Possibly the line is clogged with food waste as well.

Good luck


Dec 21, 2017 | GE 24 in. GLD5560LSS Stainless Steel...

2 Answers

2005 Chevy Avalanche Transmission Problem

i had the same problem, its the torque converter. I took my 05 c/a in because i was having shifting problem, the long and short of it is there is a breather on the tranmission that sucks in water from the road. the water and the atf dont mix. the dealer put in a torque converter and changed the fluid and installed a redesigned transmission breather.

Feb 15, 2009 | 2005 Chevrolet Avalanche

1 Answer

Wash cycle water level

the water needed needs to just come up right under the door this is how much water they use cause they use a tumble wash to clean the clothes
low water preasure is a problem but also make sure both water inlets are being used (hot and cold) even if you dont have hot attach a y hose the machine needs both inlets in use
these machines use very low water usage but they still need a fill up point

Dec 06, 2008 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4727 Answers


Level 3 Expert

78257 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides