Question about 1996 kawasaki GPZ 1100

1 Answer

When i put it in first gear ease off clutch it goes dead

1996 kawaski gpz 1100

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 101 Answers

Sounds like the bike "thinks" the side stand is still down. There is a switch on the side stand to tell the ignition if it is up or down. The intent is to prevent a person from riding off with the stand down and crashing. Check first to see if it is sticking. Observe the operation of the switch as you raise and lower the side stand. Often, a shot of lubricant can resolve this issue. If the switch is moving in and out, then disconnect it from the wiring harness and put an ohmmeter across the two leads and check for continuity and no continuity as the side stand switch is down and then up. If the plunger for the switch is moving in and out with the side stand, and you do not get a change of continuity with the side stand up or down, it will need to be replaced.

Posted on Sep 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Needing to replace the whole key switch on a 86 750 vulcan kawaski need the cheapest


Get the manufacturers original replacement part for best results. Any imitations will cause you grief ... up to and including leaving you stranded out in the middle of no where at the very worst time.

Thanks for your interest in FixYa.com

Jul 18, 2010 | 1996 kawasaki GPZ 1100

1 Answer

1998 kawaski jet ski that boggs down on take off


Sounds like this bike sat for a while. When carburetors sit, the jet's inner diameter shrinks slightly from oxidization/micro-corrosion, and the diameter of the needles that go through them grows for the same reason.

Replace the jets and the needles that go through them.

I had this problem with a Suzuki GS850. When I fixed it, I treated the bike as I had been before I fixed it on the test drive, and almost launched myself off the back of the bike when I first opened the throttle. Careful.

Jul 08, 2010 | 1998 kawasaki GPZ 1100

1 Answer

I have a 1996 gpz 1100 and the fuel tank was taken off for repair. My buddy pulled the hoses off along with the tank and doesn't remember where they went. I know one is the main fuel feed the other is a...


There are 3 hose, Fuel outlet tank vent and tap vac. The vent hose usualy goes down past the swing arm and is open to the world. the fule outlet suppies flue to the carbies and the vac tap one come from a vac port/s on the top of 1 or 2 carbies. and the other end goes tot he back of the fuel tap to turn it on.

Jun 28, 2010 | 1996 kawasaki GPZ 1100

1 Answer

No spark on bike


fuse or lose wire but sometimes stator

Sep 20, 2009 | 1997 kawasaki GPZ 500 S - GPX 500 R

1 Answer

I need proper torque specs for clutch relese springs 84 gpz 1100


You are over torquing the springs. Buy a generic manual from your automotive shop. ZX11 specs are much higher than the GPZ.

Aug 20, 2009 | 1995 kawasaki GPZ 1100

1 Answer

Finin parts that fit my bike


Try the web. Google " salvage kawasaki motorcycle parts " and google " salvage kawasaki motorcycle fairings ".

Pleas rate this solution. Thanks :)

May 06, 2009 | 1996 kawasaki GPZ 1100

1 Answer

Replacing clutch 83 gpz 1100


You will need an air gun wrench if you are intending to replace the clutch basket.If not then it is easier.But you will need some tools and a new gasket.It's not difficult though.

Mar 17, 2009 | 1995 kawasaki GPZ 1100

2 Answers

Gpz 1100


36 front...42 rear

Nov 20, 2008 | 1997 kawasaki GPZ 1100

Not finding what you are looking for?
1996 kawasaki GPZ 1100 Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...