Question about 2001 Kymco Stryker 125

2 Answers

How to get to a crankshaft on a 2000 moped 2T 50 for repair? I need to know what part I need to take off to get to the crankshaft?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 99 Answers

The crankshaft is like the heart of your engine. everything needs to be taken off to get to it. first remove the exhaust and carburetor, and anything else that needs to be removed to get the engine out of the frame. then remove both the left and right engine case covers, after draining the oil. on the left side there is going to be a large flywheel with a big nut in the center. that nut needs to be loosened with an impact wrench, and you need a special puller to get the fly wheel off. then remove the electronics mounted behind it. go to the other side, and there is going to be a large clutch basket. directly in front of that is the other end of the crankshaft. its going to have 1, maybe 2 gears with a big nut holding them on. use the impact again to remove this nut. you might have to remove the clutch basket to slide the gears off of the end of the crank. then loosen the bolts to get the cylinder off, then remove the motor mounts and get the engine out of the frame. once its out, then remove the cylinder and head, and pull the piston off. there is going to be several bolts holding the two center engine cases together. you must find and remove them all. then when those are off the engine cases should slide apart pretty easily. be careful though, because the gears on the transmission tend to slide off when your doing this, and they can be tricky to get back on their shaft. once the cases are apart, then the crankshaft will slide out. sometimes it takes a few good hits with a mallet to get it out. if you need any more detailed information, let me know. ive never worked on your specific model, but this is a basic procedure that works on almost all small engines. there may be some variations though. but for the most part, follow these steps and take your time. its going to be a good 4 or 5 hour job to replace the crank if your a good mechanic. if you have never done this before, I STRONGLY recommend you have an experienced tech do it. there are a lot of small parts, and you have to be very careful with how it is put back together. theres a lot to take into account when assembling an engine. if you do want to try it out, then I recommend you at least get a service manual, or have the guidance of a good mechanic. good luck!

Posted on Sep 08, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 163 Answers

Take the engine out and completely disassemble the engine and cases as the cases need to be split to get crankshaft out... You will want someone to help you that has more experience, as it sounds like you don't have a lot.. Not saying it's a bad thing but when it is this serious help is good...

Posted on Sep 08, 2009

  • vtrktrmn Sep 08, 2009

    Take the engine out and completely disassemble the engine and cases as the cases need to be split to get crankshaft out... You will want someone to help you that has more experience, as it sounds like you don't have a lot.. Not saying it's a bad thing but when it is this serious help is good...

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to derestrict 2003 piaggio lt50


Hi, Jane for more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
How do you derestrict scooter using Piaggio 50cc 2T engine
How to derestrict 50cc scooter
PIAGGIO Liberty 50 Catalyzed Workshop Manual
https://www.oemmotorparts.com/oem2.asp?M=piaggio
PIAGGIO ZIP 50 2T User Manual

Mar 19, 2017 | Piaggio Motorcycles

1 Answer

How can I replace cylinder?


Peugeot vivacity variator - YouTube

? 5:41
https://www.youtube.com/watch?v=VmvXD0QMHog
Aug 24, 2012 - Uploaded by James Parus
this works probably only with 50cc versions, as 125's are probably not limited at all. ..... Do you know what is the size of the rollers in vivacity 3? I just bought one and want to derestrict it and changethe rollers since they seam to be ... 2008 PEUGEOT VIVACITY 350 SCOOTER MOPED VGC 8.3K MILES 2 ...

How To Replace / Rebuild Your Brake Master Cylinder ...

? 17:43
https://www.youtube.com/watch?v=JqX2GUutPvU
Jul 2, 2014 - Uploaded by Scudo Camper
How To Replace / Rebuild Your Brake Master Cylinder .... Quickquestion - do you not use nitrile gloves to protect you from skin contamination?Missing: 2008 ‎tkr ‎50

2008 Peugeot TKR 50 specifications and pictures - Bikez.com

www.bikez.com/motorcycles/peugeot_tkr_50_2008.php
The 2008 Peugeot TKR 50 and all other motorcycles made since 1970. Specifications. Pictures. Rating. Discussions.
Search Results

    How to change cylinder on a scooter - YouTube

    ? 6:29
    https://www.youtube.com/watch?v=bUrlKLeGgjo
    May 26, 2011 - Uploaded by HasSse666
    How to change cylinder on a scooter (vivacity speedfight) ...50cc to Big Bore 80cc Scooter Rebuild/upgrade Kit How to do it Racing Upgrades ...

    50cc Cylinder Barrel Gaskets Peugeot Trekker Speedfight 1 ...

    www.ebay.co.uk > ... > Scooter Parts > Other Scooter Parts

    eBay50cc Cylinder Barrel Gaskets Peugeot Trekker Speedfight 1 I 2 II Elyseo Buxy AC in Vehicle Parts ... Intended Use: Replacement Part ... Peugeot Elyseo 50i AIR 2T 2002-2007; Peugeot Elystar 50 AIR 2T from 2008; Peugeot Elystar 50i AIR 2T from 2008 ...All pictures are taken by us so you will receive exactly what you see.

    Peugeot TKR 50 2011 Replica Cylinder Head Gasket ' eBay




Feb 03, 2016 | 2008 Peugeot TKR 50

1 Answer

What spark plug do i need for a Yamaha M S 50 moped 1986


take out the old plug and the details are on the ceramic bit
the new plug will be gapped correctly.
brand doesn't matter

Jul 24, 2014 | RTO 50cc Moped Scooter

1 Answer

2009 Aprilia SportCity One 50 2T


Hi Anonymous, for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. https://www.tradebit.com/filesharing.php/search/0/2009+aprilia+sportcity+one+50+2t

Feb 07, 2014 | 2009 Aprilia SportCity One 50 2T

1 Answer

The exhaust pipe's fractured on my SportCity One 50 2T. Any recommendations for replacement, without removing the restriction?


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. https://www.tradebit.com/filesharing.php/search/0/2009+aprilia+sportcity+one+50+2t

Oct 02, 2013 | 2009 Aprilia SportCity One 50 2T

1 Answer

Overheating


You need to change the oil, filter and need complete tuning of your piaggio.

Jun 19, 2013 | 2010 Piaggio Liberty 50 2T

1 Answer

Rakatak md150t-6 moped was running


I was riding my 150 moped and when I turn the corner it cut off. When I tried to start it back up it wouldn't start. It crank but didn't turn over...

Aug 22, 2009 | 2000 Bajaj Chetak 150

1 Answer

I need to download manual for Kymco Striker Trial motorbike 2005


Need to know what parts to take off to get to a crankshaft on a moped 2000 2T 50?

Jul 11, 2009 | 2001 Kymco Stryker 125

1 Answer

Open throttle to full. clutch wont enegage for 3 to 4 seconds


Try a new belt, it may look fine but can be polished and have no grip left.

Jun 11, 2009 | RTO 50cc Moped Scooter

Not finding what you are looking for?
2001 Kymco Stryker 125 Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...