Question about 2003 Suzuki GSX 750 F (Katana)

1 Answer

My suzuki katana some body move the screws in the carburators

Need the factory adjustment for the air mixture does not idle right and does not stay in 1000 rpm. does not run well. it was running good before the screws were moved

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 311 Answers

Hi,this might help,it is very difficult to get the adjustments right without a set of carb balance gauges,the adjustments are very small and critical to the running of the bike,borrow or buy a set of gauges,hook up the gauges,balance the left two cylinders together so they are both running exactly the same,then do the two right cylinders and get them both running the same,then match the two sets  together using the balance screw between no2 and no3 cylinders,a general rule of thumb to get a startng point is to wind the mixture screws in untill they stop,then back them out about 1.5 turns,do the same to all four screws before you start trying to balance the carbs,make sure the bike is sitting vertical or on the centre stand because if it is not it will effect the balance of the carbs and also make sure you have a good airflow over the front of the motor for cooling as it will take half to three quarter of an hour to get the balance right...most bikes need the carbs rebalanced on a regular basis because when the parts of the carbs start to wear the balance will change,a good set of carb balance gauges is a worthwhile investment...hope this helps

Posted on Sep 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust air fuel mixture


Hi Wentzpatrick, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Jul 15, 2013 | Harley Davidson XLH Sportster 883...

1 Answer

How do you adjust ldle air mixture on 2002 dyna low rider


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Apr 14, 2013 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

How do i adjust the idle on my 03 dyna wide glide


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Aug 18, 2012 | 2003 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

1999 Road King Carb Adjustment


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time, final adjustment should be made with the engine at normal operating temperature. Good luck and hace nice day.

Apr 27, 2012 | Harley Davidson FLHR-FLHRI Road king...

1 Answer

Is a 1998 95th anniversary harley davidson softail springer have a carburator


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time, final adjustment should be made with the engine at normal operating temperature. Good luck and hace nice day.

Apr 16, 2012 | 2000 Harley Davidson FXSTS Springer...

1 Answer

How do you adjust the air flow mixture on a 2005 electra glide


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Apr 01, 2012 | 2005 Harley Davidson XL 1200 C Sportster...

1 Answer

Idle set 2004 fxdwg


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time, final adjustment should be made with the engine at normal operating temperature. Good luck and hace nice day.

Feb 26, 2012 | Harley Davidson FXDWG - FXDWGI Dyna Wide...

2 Answers

05 suzuki katana 750 idle issues


Idle issues can be fuel/air (mixture ratio) or igition (spark strength). It sounds like an air restriction issue. If there is no blockage throught the air inake/filter, make sure you adjust the jets to specifications and make sure there are no float issues with the carbs.

Jan 22, 2009 | 2006 Suzuki GSX 750 F (Katana)

1 Answer

Idle speed problems


Hi Walker14,

You have to sync thecarbs and also you will have to reset the air-fuel mixture screws.
One of the carburators should be factory adjusted, I dont wn a kawasaki but I own a YAMAHA SECA XJ750R and thro it I am sharing my experince.
Once you have located the factory preadjusted carburator you can thn set the others to its specs. I use the feeler gauge to do for my bikes carburators and it works fine.
With regards to the mixture screw..... get the all in tightened but slowly aas to not damage the pin end of it!.
Start the bike and get it to normal running temp and thn set the screws 2 and half turns out...you may need to set your idling speed before you begin this setting of the mixture screws, you prolly will hveto go higher on revs or vicecersa ....onc eyou are at the mixture screws and adjusting them , you will surely note the differenc ein sound of he bike an its idling ..
Hope this will help.


Knight.

Jan 16, 2009 | 1988 Suzuki GSX 600 F (Katana)

Not finding what you are looking for?
2003 Suzuki GSX 750 F (Katana) Logo

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...