Question about 1986 Yamaha RD 350

1 Answer

Put in new battery engine cranks all the time

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

Check your start button on grip first. Then check the bendix on the starter..they sometimes stick allowing power to continue to starter.:)

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 Dodge Stratus will not start I just put a new alternator and battery in it and the mechanic told me that the engine is locked how do I unlock the engine


huh ..
you can change a battery and an alternator any time
with out "locking " the engine

does the motor crank over ?
check starter motor
check spark at plugs and fuel to injector rail

if it wont crank or start start .. then there are other issues
that may or may not have been caused by low voltage
before the battery and alternator was replaced

if the engine light is on there will be fault codes to read






26348651-g30ioc3djl54xt4sh5ag1odt-1-0.jpg

Nov 10, 2016 | Dodge Cars & Trucks

1 Answer

2004 xterra would sound sluggish when cranking. Similar to the sound a car makes if timing is off. Belts are fine. And put new battwey and terminals. Cranked fine dor two to three rimes but started doing...


while the voltage on the battery may be perfect with a multimeter on a still test , what is the battery voltage when trying to crank the engine. If the voltage drops to below 10 volts you have a battery problem. All headlights dim while cranking and the flatter the battery the greater the dim of the lights. It is bad practice to have the lights on while trying to crank the engine as the current draw for the lights takes power away from the ECM and ignition system

Dec 30, 2014 | 2004 Nissan XTerra

2 Answers

I have a 98 buick lesabre just got a new starter & battery put on this week and the car still wont start. Friday it cranked up 6 times and no more. Saturday it cranked 5 times and no more. what could...


Sounds like maybe bad battery cables , positive or the ground side ! You need to do a voltage drop test to see which one. Need to use volt ohm meter ! Put positive lead on the positive connection at battery , next put negative meter lead at the connection on the starter. Make sure the vehicle won't start by pulling fuel pump fuse. Have someone turn the and crank the engine , If the meter reads less then battery voltage while cranking that cable is bad and needs to be replaced. I'll also send a link for a you tube video on doing the test. Voltage Drop Testing the Starter

Dec 21, 2014 | Buick LeSabre Cars & Trucks

1 Answer

Put new crank pos. sensor still will not crank


the crank position sensor will never tell a vehicle to crank. the purpose of the crank position sensor is to detect misfires and also for engine timing. when a vehicle does not crank you need to look at starting system. check your battery, load test it. check for starter signal to starter solenoid from ignition switch.

Aug 28, 2014 | Cars & Trucks

2 Answers

New battery and new starter but still will not crank only clicks


More than likely the charging system is not working and allowing the battery to run down/low. Put a voltmeter on the battery and raise the engine about 2000 rpm and the battery should read 13.5-15.5 volts with all electronics on (fans switch on high, flashers, wipers, headllights, defrost etc). It should also read about 13.5 volts at idle but may not depending on the load from the accessories and voltage regulator. Most important is that it will read 13.5-15.5 volts when the engine is at 2000 rpm with the accessories on. If it does not read in that range the charging system(alternator most likely) has a charging problem.

Nov 15, 2012 | 2000 Chrysler LHS

1 Answer

First of all. We have put 2 new starters on this car recently. We thought the first might have been a fluke. However we had the 2nd checked and it tested fine as did the battery and alternator. Problem is...


what do you mean by wont start?? engine cranks but wont run? engine wont crank? Is the anti-theft light flashing? is the car in park? did you put it in Neutral and try to crank it?

Nov 19, 2010 | 1992 Saturn SL

1 Answer

Can't shut factory installed alarm off. It disables the engine. Put new battery in keyfab but still won't work. Tried disconnecting battery & waiting, still won't work. Pumped gas 3 times with...


is the security light on? Try ,crank it ,leave the ign. on for 1 min. Crank again,leave ign. on for 1 min.
should reset ,may have to do that several times.

Oct 25, 2010 | 2001 Chevrolet S-10

2 Answers

Turned key to start engine, battery was low engine only cranked three times. Turned key to off but engine was still trying to crank with the key in off position. put on battery charger and engine tried to...


stater bendex/new starter.or relay.but start with new starter.PS make sure your cables are clean AND THE BSTTREY IS HOT.a low or bad batt can do the same thihg

Nov 21, 2009 | 1995 Dodge Ram

1 Answer

99 intrepid 2.7 engine cranks alot to get started


Did the old engine start ok? If so then take a good look at the Crank Position Sensor or the flywheel sensor ring. Some times the flywheel ring can get bent/damaged during an engine swap. It doesn't take much to dent that ring and it is really close to the CPS. The other thing you can try is turn the key on without starting several times before cranking. This will pulse the fuel pump each time and charge up the fuel pressure. If that works you have a fuel pressure issue (probably a pump) Let me know how it goes.

Mar 28, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1986 Yamaha RD 350 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...