Question about 2004 Sym Husky 125

1 Answer

I have a husky pro air compressor that fails under load. 3hp, 60t

I have a husky pro that fails under load. Sometimes it works and sometimes,not.
Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 137 Answers

Sounds like bad seals to me, maybe the rubbers have perished.

Posted on Sep 20, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a husky model 947265. And it won't shut off when I turn it off manually I have to wait till all the air is out before it turns back on


Free Husky Air Compressor User Manuals ' ManualsOnline ...

powertool.manualsonline.com > ... > Husky > Power Tools Husky
Husky Air Compressor Operator's Manual ... Plumbing Quincy Single-Stage Air Compressor - 3.5 HP, 220 Volt, 60-Gallon Vertical Tank, Model Q13160VQ.

Sep 04, 2015 | Air Tools & Compressors

1 Answer

Air compressor cannot spin up with pressure in tank sometimes


There is an unloader valve and a check valve on the discharge side of the pump. The check valve is not holding and the unloader is not dumping the pressure so the compressor cannot start. Since it is new, you may want to take it back. If not you are going to be replacing parts.

Mar 10, 2014 | Craftsman 3 gal. Air Compressor, 1.5 hp,...

2 Answers

I have a 60 gallon husky air compressor with a bad 3.2hp motor. Will installing a 3hp motor hurt anything? Same rpm's(3450).


Should be just fine!
Any smaller, however, you might find the motor is laboring to run the compressor, as the motor may have been factory matched.
Be blessed.

Mar 21, 2013 | Air Tools & Compressors

1 Answer

I have a husky 7hp compressor , sometimes when i tries to start the motor buzzes and blows the breaker , but if i advance the pulley it will then start


The start capacitor is bad. Getting near the terminals can give a huge shock. so just get the value off the side and replace it.

Feb 19, 2013 | Campbell Hausfeld Air Tools & Compressors

1 Answer

Compressor starts vary slow and sometimes blows the braker


Hi anthony krim...
You will need to replace your start capicator for the motor, it is faulty
Please take time to rate me

Sep 08, 2011 | Stanley Bostitch CWC200ST 3HP Oil Lube...

1 Answer

The compressor is 3HP 230 v motor. In the pressure switch it is wired white and black from motor and green to ground. Is the white and black wire 115 volt each or it the white wire common and black wire...


If the motor is 230 v then it should have three wires, black, red, and green, however if the motor is convertible from 120 to 230v then the wire from the motor may be black, white, and green. Check the motors label to see if it has different wiring configurations. If the motor is 230 v only then the white wire would be the other side of the 230 v circuit, and the pressure switch should break both sides. Neutral is not used. Note that some people would use a single pole pressure switch, although this will work it is not recommended.

May 07, 2011 | Ingersoll Rand Single Stage Electric...

1 Answer

Brand new L3 builds to 25 psi then motor goes out on thermal overload.


Honestly if its new I would either return or ask for them to send someone out sounds like check-valve is letting air through witch is loading compressor.

May 06, 2011 | Ingersoll Rand Single Stage Electric...

2 Answers

How do you replace the regulator valve on a husky pancake air compressor? Mine just spins and will not allow me to get air to the hose


I could not find parts for my husky compressor and had the same problem as you describe. I went to lowes and purchased fittings to draw air out of the safety port. Remove the safety pop valve and install t-fittings to allow you to reinstall safety valve and also a quick connect. If you want to be able to regulate the pressure, install a simple pressure regulator before the quick connect (also avail. at lowes). This remedy is not pretty but sure works great and simple. Problem with husky regulator is stripped thread /knob. Sometimes you can turn the knob if you drain air from tank; this will release the spring tension on the regulator knob.

Dec 31, 2010 | Electric Air Tools & Compressors

2 Answers

Need manual for a Kawasaki model 840703 5gal 3hp


I called 1 800 590-3723 and they are e-mailing a manual to me. For my model (3HP twin tank) they said 10W30 or 5W30.

Jun 19, 2009 | Air Tools & Compressors

Not finding what you are looking for?
2004 Sym Husky 125 Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sym Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4818 Answers

Dave Matthews
Dave Matthews

Level 2 Expert

97 Answers

yadayada
yadayada

Level 3 Expert

78919 Answers

Are you a Sym Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...